Lift Kit that Fits 2017 Lance 1685 Trailer

Question

Question:

Do you have a lift kit for a 2017 Lance 1685 Trailer? If so could you send me a link.

asked by: Steven W

0

Expert Reply:

Since your 2017 Lance 1685 has tandem Torflex #10 axles the tandem axle lift kit you'd need is the part # K71-707-02.

expert reply by: Jameson C

0

Answer 1

To find the right size battery box for your Lance trailer, you will need to take a couple measurements to make sure it will work for you. If you want to mount it on the tongue of your trailer you need to know if it has sufficient space to handle the…

view full answer...

Answer 2

Hey Brad, thanks for all of the info on what you have. I can tell your magnets are basically toast, the brake pads look thin, and your hub/drums look like they are in bad shape too so your best option is to go with new assemblies left and right with…

view full answer...

Answer 3

Good question, and the Dexter Torflex lift kits are for square torsion axles, while the over/under kits are for standard round axles with double-eye springs. Your 2022 Lance 1995 travel trailer utilizes round 3,500 lb axles, so you will need the…

view full answer...

Answer 4

Thank you for your axle serial number. I was able to use this to determine that you need an L68149 inner and L44649 outer bearing along with a 10-19 grease seal. For a complete kit we have the Bearing Kit for #84 Spindle part #BK2-100. If you want to…

view full answer...

Answer 5

We have just the thing. For you I recommend the MORryde RV Cargo Sliding Tray #MR74FR. The overall dimension of the tray is 72" x 20" and 6-5/8" tall. So this will fit nicely in your compartment provided it is al least 72" deep…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Lift Kit that Fits 2017 Lance 1685 Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching