Replacement Hub for 10k Dexter Drum with 9-44 Marking

Question

Question:

What hub do I need for the wheel with Dexter drum with the number 9-44 on it?

asked by: John D

0

Expert Reply:

Your Dexter Trailer Brake Drum # 9-44-1 is designed to fit the Dexter Trailer Idler Hub Assembly # 8-288-3UC1. This drum and hub installs on 9,000-lb to 10,000-lb general-duty Dexter axles made prior to July 2009.

expert reply by: Jameson C

0

9-44 Trailer Hub
(click to enlarge)

Answer 1

I went out to our warehouse to measure the Dexter Trailer Brake Drum #9-44-1 drum for you. From the inside wall to the inside lip the measurement is 4-1/2 inches where it will come to the dust shield of the brake assembly where it mounts to the axle…

view full answer...

Answer 2

In regards to the B&W Tow & Stow 3-Ball Mount - MultiPro part #BW49FR, there isn't any sort of step attachment. That said, if I were you and I needed some help getting in the bed I would simply rotate the hitch balls so that the side…

view full answer...

Answer 3

Hey Kyle! The Pacbrake Alpha HD Air Bag Suspension Kit #PB22RV installs in the same location as most fifth wheel and gooseneck brackets. I would expect to have to do some drilling to install these with your B&W Turnoverball. Instead, I recommend…

view full answer...

Answer 4

Hey Mike, The #IR29FR lock kit is not compatible to work with the B&W Pintle Hitch that you have. The pin diameters are different sizes and would not fit. The only kit we have that is confirmed to fit the B&W Pintle Hitch is the InfiniteRule…

view full answer...

Answer 5

From what I have found, the ALKO hub and drum assembly you have is for 7,000 lb axles. I believe the Dexter Trailer Hub and Drum Assembly for 5,200-lb to 7,000-lb Axles - 12" - 8 on 6-1/2 #8-219-4UC3 will work as a replacement. This has the same…

view full answer...

Answer 6

Hey there Brad, We do have a replacement for the 125255UC grease seal; the correct seal is the following: - Double Lip Grease Seal #34823

view full answer...

Answer 7

The correct replacement for your 1-065-041012-01 motor is part #LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson #LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice. You'll…

view full answer...

Answer 8

While we don't have a harness that plugs into the factory port of your 2020 Jeep Grand Cherokee that has a matching end for the factory brake controller we do have this type of solution for an aftermarket brake controller like the very popular P3…

view full answer...

Answer 9

From what I could find, the MasterPro Hub PT581750 you have fits a Dexter #84 Spindle. This is one of the most common spindle available for a 3,500 pound axle, so there are definitely options available for replacements. With that being said, the…

view full answer...

Answer 10

It looks like you're likely trying to replace your hubs/drums on your Dexter axle and I do believe that the "0100" you found on the spec plate actually reads "D100" since that was one of the models that Dexter had for this…

view full answer...

Answer 11

I am sure we can help replace all of the brake components but without a brand I can't really help pin point just the hub/rotor. Instead the best we could do is a kit that replaces the hub rotors, the mounting bracket, and the calipers. So you…

view full answer...

Replacement Hub for 10k Dexter Drum with 9-44 Marking

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching