Jeep Style Trailer Fender Equivalent to American Trailers Part # 03-010

Question

Question:

We are looking for a jeep style fender that is equivalent to the American trailer part 03-010. its a single axle 16 ga cold roll steel 8w x 26l x 10 h. Do you carry anything that meets these requirements?

asked by: Mark B

0

Expert Reply:

The Single Axle Jeep Style Trailer Fender # HP99VR is going to be the closest fender we have to your dimensions. This fender is 24" long x 8" wide x 8" tall. It is constructed of 16 gauge cold rolled steel as well.

expert reply by: Bud M

0

Answer 1

We have two fenders that will fit your trailer with 20.5 x 8.0 - 10 sized tires: #HP99VR which is 16 gauge steel for 8 to 12 inch wheels #J10821 which is 16 gauge steel for 10 wheels Both are Jeep style fenders and will work for you. They're…

view full answer...

Answer 2

The etrailer Single-Axle Trailer Fender, Part #HP99VR, is shown in the attached photo with several measurements indicated. I have also included a video link which helps to show certain dimensions that are difficult to convey on the photo. The overall…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Answer 12

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Jeep Style Trailer Fender Equivalent to American Trailers Part # 03-010

Product Page this Question was Asked From

Continue Researching