Hardware Needed To Install The Redline Pre-Drilled Round Rubber Trailer Bumper

Question

Question:

What is the part # for the 9/16 bolt that is used to attach pre drilled rubber bumper to horse trailer. I’m missing a bolt and need to replace.

asked by: Sarah S

0

Expert Reply:

Due to the wide variety of applications the Pre-Drilled Round Rubber Trailer Bumper # D3-96 does not come with any mounting hardware. You'll want to use a 9/16" bolt but will need to determine the length of the bolt based on the thickness of the trailer wall you're mounting to.

expert reply by: Kevin C

0

Answer 1

To hook up a trailer jack to a 12 volt battery you need to make the connection from the jack's power wire to the positve post on the battery using a ring terminal, like part #DW05705-1. If you don't already have a battery on the trailer you…

view full answer...

Answer 2

If you can squeeze a washer through the hole with the head of the bolt, then you can absolutely use one to mount the Pre-Drilled Round Rubber Trailer Bumper - 96" Long x 2-1/16" Wide #D2-96 to your bumper, but one is not required even…

view full answer...

Answer 3

The PS-8 screws should work very well going into either material you mentioned. The threads are coarse enough that they'll get good hold on the aluminum or the rubber. For best results, you'll want to ensure that as many screws as possible go…

view full answer...

Answer 4

We have exactly what you are needing with part #D3-96 when it comes to the bumper. This is a pre-drilled round rubber trailer bumper that is 96" long (8') and has 9 holes drilled that as 11" apart on center and take 9/16" bolts.…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Hardware Needed To Install The Redline Pre-Drilled Round Rubber Trailer Bumper

Product Page this Question was Asked From

Continue Researching