What 5th-Wheel and Gooseneck Puck Covers Fit My 2022 Ford F-250?

Question

Question:

Do you have puck covers for a 5th wheel prep package for my new 2022 f250. The prep package from ford does not come with puck covers. Do you sell them. They are the 4 rectangular 5th wheel plugs and the center circular cap for the gooseneck.

asked by: Tim L

0

Expert Reply:

Yes! The parts you need are two sets of the Replacement Puck Plug Covers for Elite and Signature Series Fifth Wheel Rails # 58199 and one of the Rubber Hole Cover for Reese Elite Series Under-Bed Gooseneck Trailer Hitch # RP30136. These fit the industry standard plugs on your 2022 Ford F-250 with OEM prep.

expert reply by: Bob C

0

Answer 1

I believe what you need for your 2021 Ford F-250 Super Duty is the Replacement Puck Plug Covers for Elite and Signature Series Fifth Wheel Rails #58199 which I know you mentioned you do not need, however even though the trim ring is circular and it…

view full answer...

Answer 2

The replacement plug covers you need are the Replacement Puck Plug Covers #58199 which are a fit for the factory pucks you have in your 2014 Ford Super Duty.

view full answer...

Answer 3

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

What 5th-Wheel and Gooseneck Puck Covers Fit My 2022 Ford F-250?

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching