Is Clamp Kit Needed to Install Inno Square Bar Roof Rack on 2019 Toyota Tacoma

Question

Question:

I am interested in the Inno square bar roof rack, part # INB137 and # INSUT feet for my 2019 double-cab Tacoma. Is this the only package I need or do I need to purchase the custom fit kit as well? Thank you

asked by: Craig M

0

Expert Reply:

You're on the right track, but in addition to the the # INB137 54 inch square crossbars and the # INSUT roof rack feet, you will indeed need the # INK729 vehicle-specific clamp kit.

expert reply by: Mike L

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 4

There are a couple of differences between the two. The JetStream bars like #Y00425 are made of extruded aluminum while the CoreBars such as the #Y00421 you've looked at are constructed of galvanized steel. As you've mentioned, the CoreBar has…

view full answer...

Answer 5

Hey Bill, the Torklift ApexAnchors Tie Downs part #TL37QV that fit your 2019 Toyota Tacoma install by attaching to the frame of your truck through the bed. So you'll need to drill a hole in your truck bed and attach the tie downs to the frame…

view full answer...

Answer 6

The door clamp style of roof racks like the Inno part #INB137, #INSUT, and #INK685 do not allow water to leak into the vehicle. If you check out the picture I attached you can see that the clamp actually fits above the door seal.

view full answer...

Answer 7

The older style of Thule square bars are no longer made but I do have a solution for you. The Inno square crossbars are the exact same dimensions and will fit your Thule feet so you'd want the #INB137 for a set that is 54 inches long. The new…

view full answer...

Answer 8

Yeah, that things fun with camper shells. I've got exactly what you need though Lauren. If your Leer XR camper shell does not have tracks installed, I recommend the Rhino-Rack Heavy-Duty Roof Rack for Camper Shells item #Y01-120B with 54"…

view full answer...

Answer 9

Yes the Inno Square Crossbars part #INB137 are the same 7/8" tall and 1 1/4" wide as what the original Thule Square bars were. They will work with the older Thule Foot Packs for square bars like part #TH450. As you know they are a pass…

view full answer...

Answer 10

I went out to our etrailer.com warehouse and successfully fit the INNO square crossbars #IN434 into the Thule Traverse Roof-Rack Foot Pack. The reason they fit is because Inno and Thule square crossbars are the same dimensions, 7/8 inch by 1-1/4…

view full answer...

Answer 11

To mount feet and crossbars to your Leer truck cap with the Thule Roof Mounted Top Rack System #THTP54, you will need to select the correct length cross bars. The Thule WingBar Evo Crossbars are available in the following lenghts. 43" #TH711120…

view full answer...

Answer 12

The Replacement FootBase for Thule Tracker #753-2149 is what you currently have on the Thule tracks on your Leer shell. This footbase is for the now discontinued Thule Tracker square bar setup. You may be able to piece this system together even…

view full answer...

Is Clamp Kit Needed to Install Inno Square Bar Roof Rack on 2019 Toyota Tacoma

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching