How Do I Eliminate Slipping and Close the Gap on My Retrax XR Tonneau Cover?
Updated 11/21/2025 | Published 09/17/2021 >
Question:
my cover slips and has a gap on the non lock side. New stop for the lock might tighten this up but I still think I will have a gap on the right side
asked by: James C
Expert Reply:
I'm so sorry to hear about your cover! Thanks so much for attaching photos of the issue.
I reached out to my tech at Retrax, and he said that judging by the lack of a lock on the passenger's side, you have a Retrax XR cover. The Retrax XR will have a slight gap on the passenger's side, although this gap can be decreased. What you need to do is to adjust the white screws on either side of the clamps (on both driver and passenger side) to bring the rails in closer together. This will help decrease the gap/slipping on your cover.

Paul A.
11/21/2025
Bring them in together by how much?! How does that help?
Product Page this Question was Asked From
Replacement White Nylon Lock Stop for Retrax Hard Tonneau Covers - Qty 1
- Accessories and Parts
- Tonneau Cover
- Straps
- Retrax
more information >
Continue Researching
- Shop: Replacement White Nylon Lock Stop for Retrax Hard Tonneau Covers - Qty 1
- Video: Retrax Hard Tonneau Covers Replacement White Nylon Lock Stop Review
- Search Results: hitch extender
- Video: Review of Retrax Replacement White Nylon Lock Stop Hard Tonneau Cover - RTX44FR
- Search Results: hitch
- Search Results: curt 13609
- Search Results: trailer wiring
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Rack Receiver - Custom Fit - 2"
- Search Results: thule replacement end caps
- Search Results: replacement endcap for thule aeroblade load bars
- Shop: Trailer Hitch
- Search Results: motorcycle rack
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Shop: Replacement Clamp Adjustment Screw for Retrax Hard Tonneau Covers - Qty 1
- Shop: Tonneau Cover
- Video: DIY 2008 Ford F-150 Installation for the Curt Trailer Hitch Receiver
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: How to Put On Your Stealth Hitches Hidden Rack Receiver - 2026 Mercedes-Benz GLC
- Shop: Fifth Wheel Hitch
- Video: Set up: Yakima EXO Swing Away 2 Bike Rack w/ Cargo Carrier on a 2021 Mercedes-Benz Sprinter 3500
- Shop: Trailer Wiring
- Video: Easily Install Your etrailer Class III Trailer Hitch - 2016 Audi Q5
- Video: How to Install Your EcoHitch Class III Hidden Trailer Hitch - 2026 Toyota Camry
- Q&A: Instructions for Replacement White Nylon Lock Stop for Retrax Hard Tonneau Covers
- Article: How to Mount a Truck Bed Camper
- Q&A: Replacement Lock Stop for Retrax Retractable Tonneau Cover
- Q&A: Replacement White Nylon Roller for Retrax XR Tonneau Cover
- Shop: Suspension Enhancement




Gary
8/13/2024
Hello, not sure how old this is. , I think I had the same issue on my retrax XR on a 2024 Ford f-250. When fully closed it stayed closed, but anytime I try to leave a partially open it would slam forward when I hit the brakes even the lightest bit. The right side set screw was not touching at all. I tried to adjust it to its longest length and it did not reach. I ended up loosening this bolt and then sliding the mechanism as far right as it would go before stopping. Seems to have done the trick. I believe adjusting the white screws only brings the rails closer for their part but would not help the customer with the question.