Will Draw-Tite 76432 Hitch fit 2019 Jeep Grand Cherokee w/ Removeable Panel in Bumper Fascia

Question

Question:

good morning, Will this hitch fit my 2019 Grand Cherokee Limited X? I have the factory removable facia panel. Thanks

asked by: DAN L

0

Expert Reply:

According to Draw-Tite, their 76432 hitch which we sell as part # DT38MR is a fit for the 2011-2021 Jeep Grand Cherokee with the OEM fascia panel that's removeable. You can see how the hitch fits on the vehicle by clicking the provided link to a video showing the hitch being installed on a 2020 Grand Cherokee with the bumper fascia panel.

If you'll be towing with the hitch, you'll also need a trailer wiring harness like # 118727, a ball mount like # D-4, Hitch Pin and Clip, # PC3, and for a trailer ball, use # 19260 for a 1-7/8 inch or # 63845 for 2 inch ball.

expert reply by: Mike L

0

Answer 1

It is completely within the realm of possibilities that the actuator has become disconnected from the gate internally causing the valve to not open. The Valterra Waste Valve Body for RV Black Water Tank w/ Coupler, Seals, and Hardware - 3"…

view full answer...

Answer 2

Hey Will, thanks for reaching out! The etrailer Trailer Hitch Receiver #e98901 does NOT have a concealed crosstube. I'm not sure why we had that listed out like that, but I've sent in an update to get that corrected. The only hitch for your…

view full answer...

Answer 3

So the difference is purely in how the two connect to your sewer pipe, which will also tell you which one you need; one will slide into the pipe (the spigot) while the other will slide onto the pipe (the hub): - Slide Into Pipe: Valterra Waste Valve…

view full answer...

Answer 4

Hey Chuck! We do have a hitch that sits behind the removable bumper panel. What you need is the Draw-Tite Max-Frame Trailer Hitch #DT38MR. It installs behind the bumper so it is only visible when the bumper panel is removed, just like the OEM hitch.…

view full answer...

Answer 5

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

It sounds like the problem you are having is related to one of the possibilities you have mentioned. It is nearly impossible to press a race in straight at home unless you have the proper equipment and have done it before. Taking the drums to a brake…

view full answer...

Answer 8

If you want to go to the next size up from a 5.30-12 tire you will need to look at 13 inch wheels and tires ST175/80-13. For a wheel and tire combo with 5 on 4-1/2 bolt pattern and radial tire use #AM31985. This tire will be 7 inches wide and 24.1…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Will Draw-Tite 76432 Hitch fit 2019 Jeep Grand Cherokee w/ Removeable Panel in Bumper Fascia

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching