Replacement Transfer Switch for Parallax ATS501

Question

Question:

Looking to replace a Parrallax ats501 transfer switch. 2009 Holiday Rambler Endeavor. Suggestions?

asked by: Tom M

0

Expert Reply:

Your Parrallax ats501 transfer switch is a 50 amp transfer switch like what the Progressive Dynamics Transfer Switch - Metal Case - 50 Amp # PD52 that you referenced was designed to replace. This would be a solid choice that would work great and be very reliable long term.

I attached a review video for this for you to check out as well.

expert reply by: Jameson C

0

Answer 1

I would be happy to help! Since your brake assembly is stamped K23-462-00 you will want to go with the Dexter Electric Brake Assembly for 4.4K Axles #K23-462-00 and you can confirm that this is the correct assembly and not just an incorrect sticker…

view full answer...

Answer 2

Though you can tow a 2021 and 2022 Mazda front wheel drive CX-5 behind an RV with a dolly, like the Demco Kar Kaddy X #DM9713093, it cannot be flat towed with all 4 wheels on the ground, unfortunately. This does come directly from Mazda and will most…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Replacement Transfer Switch for Parallax ATS501

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching