Can an Awning Switch Be Added Outside on a Trailer?

Question

Question:

when I order this product is it possible to buy an extra switch so I can wire one switch inside and one outside in the pass-through? Would both switches work separately? Thanks

asked by: Tim R

0

Expert Reply:

There should be no issue wiring a separate switch on the outside of your trailer. However, there won't be a way to do this without hardwiring the # LC285500 into your current switch.

I should also mention that this isn't typically used outside, so it is not weather proof. If you do end up mounting it outside, it should be done somewhere protected from the rain.

expert reply by: Lazer S

0

Answer 1

I called and spoke to the technician at Lippert about the gear packs. If the arms that attach to your slide out are 2 x 2 you will need Gear Pack part #LC281331. If the arms that attach to the slide out at 2.5 x 2.5 you can certainly use Gear Pack…

view full answer...

Answer 2

To remove the old pin you'll need to remove the cover, remove the two retaining pins, and then slide the old pin out. To install the #LC93FR you'd just reverse the process.

view full answer...

Answer 3

I can definitely help with that, Larry! There are differences between the Roadmaster Comfort Ride Kits #RM-2460-2580-3 #RM69NQ and #RM-2460-2570-3 and I have them listed below. They all include the Comfort Ride Shock Absorbers for Tandem Axle…

view full answer...

Answer 4

When choosing the slider you want to measure the outside front of box width including the flange. Then you need to select a slider that extends a minimum of 2-1/2 inches beyond each side of the box width. For example, the Black Solera Slider…

view full answer...

Answer 5

Based on the pictures you definitely need the awning support arm #LC281154. I can't tell in that other photo if the pin is bent or damaged, or just barely hanging in there. I'm also not sure if your idler head and roller endcap are ok or not…

view full answer...

Answer 6

Hey Jeff, You will want to make sure the original awning on the camper is a Solera. If it is then yes this conversion kit #LC329251 will work just fine for you. There should be a sticker or tag somewhere that says the awning brand and model. If it is…

view full answer...

Answer 7

The Solera Manual Retractable Awning to Electric RV Awning Conversion Kit in Black #LC329251 or White #LC329250 like you found can only be used with Solera awnings. If you have either a Dometic or Carefree awning on your 2010 Winnebago Aspect 30C you…

view full answer...

Answer 8

I would be happy to help! As long as your manual pull down awning is a Solera, Carefree, or Dometic you will be able to use the Solera Manual Pull Style to Power Awning Conversion Kit in Black #LC329251 or White #LC329250 to convert your pull down…

view full answer...

Answer 9

To convert your Dometic manual awning to a power unit, you can use the Solera 12V Conversion Kit in Black #LC434723 or White #LC434724 if you have a manual crank system. These Solera kits are compatible with Dometic (A&E) awnings like what you…

view full answer...

Answer 10

Hey Ken, yes the key to picking between the two is which is going to fit better on the side of your camper. You can measure the height of the arms you have now and they will most likely be either 63 inch or 69 inch and you go then go with either the…

view full answer...

Answer 11

I attached a wiring diagram for the Solera Power Awning Switch Kit #LC285500 for you to check out.

view full answer...

Can an Awning Switch Be Added Outside on a Trailer?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching