Troubleshooting Brake buddy on Jeep Wrangler Unlimited
Updated 03/26/2021 | Published 03/24/2021
Question:
Brake buddy set up fine, brake away switch install seemed simple enough. The I ran the Brake Buddy through its bleeding process and on the final push it stayed in. I trouble shot the wiring again but could not find a problem . It seems like the brake away is telling it to apply full brakes all the time????
asked by: Robert S
Expert Reply:
If you are of the impression that a faulty signal is being sent from your Brake Buddy, # HM39524, I suggest you remove all power for no less than 15 minutes allowing the unit to reset. We want to ensure you do not have any vacuum pressure built. If on resuming testing you have a repeated error in operation check the signal from your breakaway switch, ensure switch is fully seated. From the Tech Rep at the manufacturer, they also suggest that you double check wiring at switch housing to ensure the brown and red wires are not touching, this could cause a false signal to engage the brake away.
Ensure the unit is placed level on the floor of vehicle, adjusting the risers as needed. Leverage of the actuating arm is effected if not adjusted correctly the goal is that the arm is level/parallel to the floor.
Product Page this Question was Asked From
Brake Buddy Select 3 Portable Flat Tow Brake System - Proportional
- Flat Tow Brake System
- Brake Systems
- Proportional System
- Every-Trip Setup
- 12V Outlet
- Portable System
- Power Assist Brake Compatible
- Air Brakes
- Air Over Hydraulic Brakes
- Hydraulic Brakes
- Wireless Display
- Brake Buddy
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: wheel only
- Search Results: wheel
- Search Results: 3035
- Search Results: e~track
- Search Results: 145/80~12 trailer tires and wheels
- Shop: Battery Disconnect Switch with Lock
- Video: Fit Test: Yakima HighRoad Roof Bike Rack on a 2019 Toyota Tacoma
- Video: Feature Breakdown: Second Vehicle Kit for Brake Buddy Flat Tow Brake Systems
- Shop: Second Vehicle Kit for Brake Buddy Flat Tow Brake Systems - Classic II and 3 - Select II and 3
- Search Results: 57341
- Search Results: 14" wheel
- Shop: Erickson Ratchet Tie-Down Strap w/ Web Clamp and Double Flat Hooks - 2" x 40' - 3,300 lbs
- Shop: Roadmaster Battery Disconnect for Towed Vehicle w/ Flat Tow Brake System - Gas Only
- Shop: Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - GM
- Shop: Replacement Hitch Tite Anti-Rattle Hitch Pin for Saris Bike Racks with 1-1/4" Shanks
- Shop: Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford, Lincoln, Mercury
- Q&A: Correct Replacement Parts for a Ventline VD0434 Roof Vent
- Shop: Vehicle Tow Bar Wiring
- Shop: Trailer Wiring
- Video: An In-Depth Look at the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Video: Best 2019 Jeep Wrangler Flat Tow Set Up RM-154
- Video: Install: Hopkins Custom Tail Light Wiring Kit for Towed Vehicles on a 2004 Jeep Wrangler
- Q&A: Troubleshooting Brake Buddy Classic 3 Transmitter Loose and Not Transmitting
- Article: Must-Have Flat Towing Components
- Shop: Base Plate for Tow Bar
- Shop: Vehicle Tow Bar Brake System
- Q&A: Does Charger Included with Brake Buddy Portable Supplemental Braking System Need to Be Installed
- Q&A: Will a Portable Braking System Drain the Battery on my 2020 Jeep Gladiator?
- Q&A: Does Rubber Mat Need to be Removed to Install Brake Buddy Select 3
- Q&A: Brake Buddy Braking System That Fits A 2021 Jeep Wrangler
on Flat Tow Brake System
