Options For Replacing 10,000 lb Atwood A-Frame Trailer Coupler

Question

Question:

I have a Atwood Mobile Products 10,000 lb a frame coupler. Im trying to find a repair kit, but I dont know what is what. I wanted to upload a picture of it to the QandA, but didnt see how. I dont see a part number on it. The only number I see that doesnt go with other things is 3063.

asked by: Greg K

0

Expert Reply:

Atwood is no longer in business, and because repair kits and replacement parts are manufacturer specific, the best option available is going to be a replacement A-frame coupler. While I'm sure this isn't the news you wanted to hear, there are a couple of options that won't break the bank:

- Fulton A-Frame Coupler - Wedge Latch # F44305R0317

- Sleeve-Lock A-Frame Trailer Coupler - Flip Latch # CA-5296-B

Both of these are weld-on couplers that accept a 2-5/16" hitch ball and will be able to replace your Atwood coupler. I have added links below to video reviews for you to check out as well of both couplers.

expert reply by: Kyle S

0

Answer 1

I have another option that may work better for you, but unfortunately we do not have a version of the Sleeve-Lock A-Frame Trailer Coupler - Flip Latch - Black - 2-5/16" Ball - 12,500 lbs #CA-5296-B for an 18 degree angle frame. The closest…

view full answer...

Answer 2

The Sleeve-Lock A-Frame Trailer Coupler part #CA-5296-B is designed for a standard 50 degree a-frame trailer. If you have an a-frame trailer then this is likely what you have as I would say a good 95% of a-frame trailers use the standard 50 degree…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 5

That is correct the inner dimension of the Demco A-Frame Trailer Coupler item #DM14793-95 is 10 3/4 inches. I have attached a picture that breaks down the measurements. You would need to fabricate a spacer on either side to attach this coupler to…

view full answer...

Answer 6

Hey Max. To attach the T-One Vehicle Wiring Harness item #118648 to your new Curt Hitch item #C13343, you'll need the No-Drill Mount Bracket item #18136 and the Mounting Bracket 4-Pole Flat item #18144. The No-Drill Mount Bracket item #18136 uses…

view full answer...

Answer 7

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hello, Phil! We do carry replacement wheel studs. The DeeMaxx drive-in wheel stud part #DE53GR would get pressed in from the back of the camper hub so that you can mount your rim to it. I've included a picture below showing all the dimensions of…

view full answer...

Answer 11

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Options For Replacing 10,000 lb Atwood A-Frame Trailer Coupler

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching