Replacement Actuator for Dexter 48867 80LP

Question

Question:

Tied down, or Dexter, 48867 80LP actuator rebuild kit? W master cylinder, slide cuff, hardware, etc...?

asked by: Robert J

0

Expert Reply:

That is a Tie Down repair kit part number I was able to find elsewhere online but we do not have ability to get. Easiest solution we have would be a new 8,000 lb rated surge actuator from Titan with the part # T4747210 and you'd be set.

expert reply by: Jameson C

0

Answer 1

Hey Jason, I am not finding much on the numbers Bass Pro gave you as replacements. What I can find on the leaf springs is that they are 25-1/4" long, and you want to stay with that same size. For that we do have a leaf spring #e68SR that is that…

view full answer...

Answer 2

Hey Brian, we have a replacement inner member for the TDE LP8500 you have with the part #DX97UR. This replaces the inner portion of the actuator and allows you to leave the outer part attached so you don't have to do any welding.

view full answer...

Answer 3

The Demco Hydraulic Brake Actuator #DM8750311 can be used to replace your Tie Down Engineering LP8000 actuator. The Demco comes with an electric lockout like you are wanting. It is zinc coated for corrosion resistance and fits a 2-5/16" hitch…

view full answer...

Answer 4

Hey Rick! I'm sorry to say there are no replacement parts that will fit the old actuator. Any inner member or other parts from other brands wouldn't line up correctly in that housing for an easy swap. The only solution is to remove it and…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Actuator for Dexter 48867 80LP

Continue Researching