Which Front Mount Trailer Hitch Receiver For a 1999 Ford Excursion

Question

Question:

do you have a front hitch to fit this vehicle.

asked by: Scott D

0

Expert Reply:

I reached out to Curt directly and found that the Curt Front Trailer Hitch Receiver # 31114 will work on your Ford Excursion.

From my research Ford started production of the Excursion in September of 1999, but labeled them as 2000 model year vehicles.

I included a picture of the Curt # 31114 for you to take a look at.

expert reply by: Samuel C

0

Answer 1

The front mount trailer hitch I recommend for your 2005 Ford F-350 is the Curt Front Mount Trailer Hitch Receiver part #31114 because it is made in the USA and currently our most cost effective option for a front mount hitch. I called Curt and they…

view full answer...

Answer 2

The difference between the Curt Hitch #C31014 and Curt Hitch #31114 is that the #C31014 is designed for vehicles with blocker beams and the #31114 is designed for vehicles without the blocker beam. You will want to look under the front end of your…

view full answer...

Answer 3

Since the Curt Front Trailer Hitch Receivers #C31014 and #31114 both use different mounting locations you will be able to have both on your 1999 Ford F-350.

view full answer...

Answer 4

Hey Ryan, yes the Firestone Air Bag and Compressor kit part #F24XV that you referenced is a confirmed fit for your 2026 Ram 2500 Power Wagon. Are you planning on towing a heavier trailer?

view full answer...

Answer 5

Hey Alan, welcome back! The Velit Diesel RV Heater for Camper Van #VE66QV is capable of heating a trailer that size. However, a major factor in how effective it is will be the insulation on the trailer. Even with adequate installation it may be…

view full answer...

Answer 6

Hey Melvin, we have the Curt front hitch part #31053 that is a fit for your 2014 Ford E450 Class C motorhome and would work great to carry a bike rack with. Do you have a bike rack already?

view full answer...

Answer 7

I am glad to hear you and your horses are all right after the hitch broke while you were driving! For your 2000 Ford Excursion I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2" #C14011 as it is confirmed to fit your…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Which Front Mount Trailer Hitch Receiver For a 1999 Ford Excursion

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching