Does BOLT Hitch Lock # BL7023585 Fit 2020 Ford F-350

Question

Question:

I notice your list of locks only go to 2018 will one of your locks work with 2020 Ford F 350 super duty.

asked by: Gary P

0

Expert Reply:

Yes the Bolt hitch lock part # BL7023585 does fit your 2020 Ford F-350. If you are unsure then you can check the attached picture that shows all of the key styles it fits.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Yes, the Draw-Tite Ball Mount for 3" Hitches #40701 will fit your 2021 Ford F-250 with the 3" receiver. The ball mount has a 6" drop or 4" rise depending on how you place it in the receiver. You will need a hitch ball with a…

view full answer...

Answer 2

Yes, you're on the money because the most popular B&W Tow & Stow ball mount for 2 inch hitchers is indeed the one that has a maximum of 5 inches of drop or 5-1/2 inches of rise. There are actually two versions of this, one being a 2-ball…

view full answer...

Answer 3

Yes, it will so long as your Ford key looks like one in the picture below. The Replacement Lock Cylinder for BOLT Toolbox Latch item #BLT79FR only works with Bolt tool boxes. If not you will need item #BL7022698.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Does BOLT Hitch Lock # BL7023585 Fit 2020 Ford F-350

Product Page this Question was Asked From

Continue Researching