Trailer Fenders Compatible with 4.80-8 Tires

Question

Question:

I have a 4.80-8 trailer tire and the fenders need replacing. What fenders do you have available that will work with this size tire? Thanks

asked by: Anthony B

0

Expert Reply:

For your 4.80-8 tires, I recommend the Single Axle Trailer Fender w Top Step - Style C - Black Plastic - 8" to 12" Wheels - Qty 1 # F008551. I've linked a review video of this fender and have also linked the page to all the fenders we carry compatible with your tire size if you are looking for a different style or color.

expert reply by: Jason S

0

Answer 1

The recommended brackets to use with the Fulton fenders part #F008551 is the #CE26061G-2. I attached a picture that shows how a customer used these brackets with this fender for you to check out as well.

view full answer...

Answer 2

All of the products you listed will work together just fine. Keep in mind, if your current springs are not 26 inch springs, like the #e77SR you referenced, your hangers, #APS4, will not be in the exact same position as your current ones. When…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Trailer Fenders Compatible with 4.80-8 Tires

Featured Help Information

Miscellaneous Media

Continue Researching