Dimensions for Firestone Replacement Axle Strap Bracket # F5433

Question

Question:

Can you gave the measurements for this part?

asked by: Gustavo C

1

Helpful Expert Reply:

I went out to our warehouse to take some measurements on the Firestone Replacement Axle Strap Bracket # F5433 that you referenced.

I measured an overall length of 7-3/8" and a width of 1-1/2". Between the two bolt holes, center to center, there is a distance of right at 6-1/2". The inside width of the bracket (between the outer walls) is 1-1/16" inches.

I have attached a couple images as well to assist.

expert reply by: Chris R

1

click to enlarge

Answer 1

Hey Kyle, good to hear from you again! You can definitely upgrade the suspension components on your 2019 Grand Design Momentum 381M in increments because the 7K and 8K brakes match enough that it can work out that way, you just need to make sure the…

view full answer...

Answer 2

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Dimensions for Firestone Replacement Axle Strap Bracket # F5433

Product Page this Question was Asked From

Continue Researching