Comparing the Square Direct Weld Jack TJD-12000SP-F2 and TJD-12000SP-R2

Question

Question:

What are the differences between TJD-12000SP-R2 and TJD-12000SP-F2 ?

asked by: Allen M

0

Expert Reply:

The main difference between the Square Direct Weld Jack part # TJD-12000SP-F2 and part # TJD-12000SP-R2 is the location of the plunger for the drop leg. The former has the plunger on the side of the crank handle and the latter has the plunger adjacent to the crank handle. Furthermore, the former has a 1-1/4" diameter jack screw and the latter a 1" diameter jack screw.

Aside from the location of the plunger and size of jack screw, the jacks are essentially the same.

expert reply by: Conner L

0

Answer 1

I do have an option for you but the drop leg plunger pin cannot be relocated, you will instead need to purchase a different jack with plunger pin in the correct location for your needs. The Square 10K Direct Weld Jack for example is offered with two…

view full answer...

Answer 2

If you aren't familiar with a jack like Square Direct Weld Jack #TJD-12000SP-R2 it can have a little bit of a learning curve. Here is how it works: As you probably know the jack leg retracts quickly. First make sure the jack is not supporting a…

view full answer...

Answer 3

The Square Direct Weld Jack part #TJD-12000SP-F2 can be used in tandem. The only thing you would need to do this would be a cross shaft which would be some sort of bar that attaches the two output shafts to one another. This is assuming you want both…

view full answer...

Answer 4

The trailer tire and wheel combination #AM3S862 is received from the supplier already with the tire mounted on the wheel. The supplier does not balance the combination, but when the tire is installed to the wheel they will line the high (heavy) spot…

view full answer...

Answer 5

Hey Bob, thanks for reaching out. We do have pins that will work with the etrailer Adjustable 2-Ball Mount #e66PR. There is not a direct replacement for the pins available, but you can use the Replacement Pins and Clips for Curt Adjustable Channel…

view full answer...

Answer 6

Hey Colin! I reached out to Swing King and they said the trailer tongue will slide in approximately 3-1/2" on either side on the #TD88FR. With an overall length of 18-1/4" you're adding about 11-1/4" to the tongue. I went ahead and…

view full answer...

Answer 7

Good news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears #TJD-12000-RODNUT in the #12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically,…

view full answer...

Answer 8

Hello Heath. I do appreciate you reaching out, but I am sorry to say we do not offer a gooseneck coupler inner tube with a 3-3/4" OD. Everything we have is a standard 4" tube. Do you know the brand of your gooseneck coupler? At this point…

view full answer...

Answer 9

I went ahead and linked the video you are referencing about rebuilding a square jack like the Square Direct Weld Jack #TJD-12000SP-F2 from our website to this answer. We have a number of replacement parts in that video and some that were not included…

view full answer...

Answer 10

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 11

The Dexter part number 023-357-00 is a 12x2 electric brake assembly. The correct RH assembly to use to replace what you have would be the part #23-459 and for the LH assembly you would want the part #23-458 if you have 6K axles. If you have 7k axles…

view full answer...

Comparing the Square Direct Weld Jack TJD-12000SP-F2 and TJD-12000SP-R2

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching