Availability of RV 4 Step that is 24 inches Wide

Question

Question:

Do they make this picture these are my measurements but in a 4 step?

asked by: Robin

1

Helpful Expert Reply:

Hickory Springs does offer a 4 step model of their RV pull out steps with the part # SMFP-4400. These have the same dimensions as the triple step as well as same step design so it's exactly what you are wanting.

expert reply by: Jameson C

1

Answer 1

I have a solution for you but we don't have a replacement bracket to replace the support and bolt that was broken on your TorkLift GlowStep similar to the #TLA8004 . Instead you would need to use the Add-A-Step for TorkLift GlowStep Revolution…

view full answer...

Answer 2

The best option we have to replace the Lippert Radius Quad Steps 432693 is with the Alumi-Tread Manual Pull-Out Step part #LC432698. I spoke with Lippert and they stated this is the only available replacement for the discontinued model. Please note,…

view full answer...

Answer 3

The bolt to bolt distance on the Flexco Manual Pull-Out Steps for RVs, #SMFP-4400, measures 28-1/8 inches and the sliding bolt at it's highest point is approximately 3-1/2 inches below the mounting base. I have attached a dimensional diagram for…

view full answer...

Answer 4

The Lippert Alumi-Tread Manual Pull-Out Step, #LC432698, has a mounting base that measures 28 inches wide x 9-1/2 inches deep. See the attached picture. If your 2017 Heartland Sundance trailer has similar measurements, then the Lippert step assembly…

view full answer...

Answer 5

I do have options for you but the Alumi-Tread Manual Pull-Out Step for RVs - 8" Drop/Rise part #LC432698 (358991 is the manufacturer part number) will not fit properly because the opening on your trailer is 28" and the frame of the steps is…

view full answer...

Answer 6

That is hard to say, but what you can do is check out the dimensional picture I attached for the Flexco Steps part #SMFP-4400 and compare them to what you have to see how they would compare to what you currently have.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Availability of RV 4 Step that is 24 inches Wide

Product Page this Question was Asked From

Continue Researching