Solution for Needing Replacement Zerk Fitting for Wet Bolt on Trailer Suspension

Question

Question:

what size are zerk fittings on dexter wet bolts broke two off

asked by: Dan

0

Expert Reply:

I reached out to the manufacturer and the Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs - 3-5/16" Long # 126B2 is a pressed in zerk fitting, so it cannot be replaced. This is also true for Dexter bolts as well. There are not threaded zerk fittings available for this bolt size, so it will require purchasing new bolts to have those working zerk fittings.

expert reply by: Jameson C

0

Answer 1

It would the easiest if you just replaced the bolt you have with the part #34007-187-00 which is the correct bolt replacement for your EZ Flex equalizer part #K71-358-00. The zerk fitting replacement info is not available.

view full answer...

Answer 2

It sounds like there might just be a clog in either the Zerk fitting or line of the wet bolt preventing grease to pass through. Aside from removing it and trying to clean it out replacement would be the only other option. Depending on the length of…

view full answer...

Answer 3

Yes, the Grease Zerk #LC44XV for your Lippert Tandem Axle Equa-Flex AP Kit #LC64FR can be replaced as it is removable. Do note that this grease zerk is specific to Lippert as it has a special tapered thread that is not commonly used by other…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

The Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers #RM-2460-2570 will not include wet bolts. This is due to the system using slipper springs to replace the double eye springs that come on most trailers. With the slipper springs…

view full answer...

Answer 6

Hi Glen, It's good to hear from you again! If you're wanting to switch to the Roadmaster Comfort Ride system with the leaf spring, equalizer, and shock absorber upgrades, I recommend using the Roadmaster Comfort Ride Leaf Spring Suspension…

view full answer...

Answer 7

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Answer 8

Hey Mike, so MORryde does strongly recommend using bronze bushings with their X-Factor brace. Nylon just wears out quicker. Do you have the older 2 inch wide springs or the 1-3/4 inch wide springs?

view full answer...

Answer 9

We recommend having a minimum of 3" between the top of the tire and bottom of the fender in order to allow for proper suspension travel. However, based on the photo you sent I believe you need new leaf springs as the ones you have appear to be…

view full answer...

Answer 10

The Kodiak Disc Brake Kit #K2HR10A11RERR is actually specifically designed to fit an AL-KO 10k #99 spindle, so this will be a perfect replacement. Though this does include the oil cap, it should be noted that it does not include the bearings or seal.…

view full answer...

Answer 11

I would be happy to help! The Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers - Tandem 7K Trailer Axles #RM-2460-2570 is for trailers that have 7000lb tandem axles, and use springs that have a 3500lb capacity each (one spring on…

view full answer...

Solution for Needing Replacement Zerk Fitting for Wet Bolt on Trailer Suspension

Product Page this Question was Asked From

Continue Researching