Recommended Trailer Axle Bearing Dust Cap Compatible with 2.10 Inch Hub
Updated 09/03/2024 | Published 10/15/2018
Question:
I have a homemade trailer that was missing an axle bearing dust cap, previous owner had a cut coke can over the outer diameter of the hub. 1.98 dust cap is too small. a 2.44 is way too big. It is hard to get a good measurement but I think I need one about 2.10inch do they make such a thing?
asked by: Lester Y
Expert Reply:
That is not a typical grease cap/dust cover size, however we do have the Bearing Buddy Bearing Protectors # BB2080 which measure 2.08 inches. These caps actually make maintaining the bearings much easier and more convenient as well. I've attached a couple videos to assist. The precise measurement using a digital caliper that can measure to the nearest thousandth of an inch is best.
Product Page this Question was Asked From
Bearing Buddy Bearing Protectors - Model 2080 - Chrome Plated (Pair)
- Trailer Bearings Races Seals Caps
- Caps
- Bearing Protector Grease Cap
- 2.08 Inch
- 3500 lbs Axle
- Bearing Buddy
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Bearing Buddy Bearing Protectors - Model 2080 - Chrome Plated (Pair)
- Shop: Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Shop: Bearing Buddy Bearing Protectors - Model 2080T-SS - Threaded - Stainless Steel (Pair)
- Video: All You Need to Know About the DeeMaxx 10" Hub/Rotor Assembly
- Search Results: axle kit
- Q&A: Are Trailer Spring Seats Needed for Square Axles with Leaf Springs?
- Shop: Bearing Buddy Bearing Protectors - Model 2047 - Chrome Plated (Pair)
- Shop: Bearing Buddy Bearing Protectors - Model 2080SS - Stainless Steel (Pair)
- Shop: Bearing Buddy Bearing Protectors - Model 2240 - Chrome Plated (Pair)
- Shop: Bearing Buddy Bearing Protectors - Model 1968 - Chrome Plated (Pair)
- Q&A: Troubleshooting a Loose Bearing Buddy Fit
- Q&A: Correct Bearing Kit For Dexter 8-247 Hub on E-Z Lube Spindle
- Q&A: Recommended Water Heater Alternative To Replace an Atwood 96110 Water Heater
- Video: The Low-Down on the Square BT8 Spindle for 2,000-lb Trailer Axles
- Video: Trailer Idler Hub Assembly for 2,000-lb Axles Spec Review
- Q&A: Replacement Grease Caps for a Trailer Hub with 2-1/16 Inch Hub Bore
- Q&A: Reverse Lockout Solenoid For Dexter DX12.5 Actuator
- Q&A: Looking For A Replacement Actuator For My Titan 10 Surg-O-Matic
- Article: How to Tell the Weight Rating of a Trailer Axle
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?
- Article: Trailer Tire Sizing
- Article: Best Boat Trailer Tires
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Boat Trailer Guides: Which are the Best?
Nick B.
9/1/2024
I have the same axle measures 2.1 in. And the 2080 bearing buddy’s are to small. Can not find a cap anywhere !