Valterra RV Water Inlet Bayonet Cap Inner and Outer Diameter Measurements

Question

Question:

What are the ID and OD measurements of this cap. Looking for a cap for our 2006 Monaco. Thank You

asked by: Vern

1

Helpful Expert Reply:

The Valterra Water Inlet Cap and Strap for RVs - White - Gravity Fill # A0120SVP has an inner diameter between tabs of 1.5 inches. and inside diameter without tabs of 1.64 inches. The outer diameter is 1.96 inches. I've attached a photo to assist.

expert reply by: Jason S

1

click to enlarge

Answer 1

Hey Ross, it doesn't look like we have GE AC unit air filters but I was able to find out that GE does sell them. There are quite a few part numbers for filters so I would need to know which specific model of GE AC unit that you have to see what…

view full answer...

Answer 2

Charles, it looks like the Predator 5000 generator you have is a bit a too big so it's not going to work with the MORryde RV Generator Slide Out Tray #MR89RR. You'd need to use a bigger tray like the MORryde RV Cargo Sliding Tray #MR37FR…

view full answer...

Answer 3

Hey Joe, The Greystone Built-In RV Microwave #GR59FR measures 17" High x 25.7" Wide x 17.3" Deep according to the specs on the instructions. Does this match what you're needing, or do you have different dimensions you're…

view full answer...

Answer 4

We do have hoses which may work for you. The MB Sturgis Propane Pigtail #100833-24 is a type 1 cylinder connection with a 1/4" male inverted flare. This is a 2 foot hose, though we also have a 15" hose #100833-15 and 1 foot hose…

view full answer...

Answer 5

I have an option for you, but I spoke to my contact at Bulldog to try and get a replacement cross shaft for you and he said they are not available. He said that you will just need to get a 12 inch long section of 1 inch cold rolled steel and then…

view full answer...

Answer 6

I was able to find the 126003 hub and was able to determine that it is a 3,500 lb hub/drum with a 5 on 4-1/2 inch bolt pattern just like the #AKHD-545-35-K that you referenced. This hub will work as a replacement for your Lippert.

view full answer...

Answer 7

Lights like the LED Clearance or Side Marker Trailer Light w/ Reflector #MCL0032RBB are more or less universal so as long as the light you're wanting to replace on your 2019 Heartland Landmark Newport 5th Wheel measures 2" x 4" overall…

view full answer...

Answer 8

In order to replace the slide on the screen door you can either measure the existing slide or the track that houses the slide. If you don't have the existing slide then all you'd need to do is measure the track that it sits in. The vast…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Valterra RV Water Inlet Bayonet Cap Inner and Outer Diameter Measurements

Product Page this Question was Asked From

Continue Researching