Electric Landing Gear Legs for a 2017 Sundowner 3H GN Super Sport Horse Trailer
Published 05/29/2018 >
Products Featured in This Question
Question:
Thank you very much for your help. So I have a RAM landing gear. For the Velocity series will I need the adapter still? I saw you also carry a RAM Electric motor. Will that work for my application. Thanks again. Oh, I was also looking at purchasing a BX1 GN coupler. Will that work for my trailer or is that specific to Bulldog as well.
asked by: Nicholas
Expert Reply:
For starters, the Bulldog Powered-Drive Kit part # BD1824200100 for single speed or part # BD1824180100 for two speed is only designed to work with Bulldog landing gear legs that have a 12,000 lb support capacity. If you do not have these legs than I cannot confirm the conversion kit will work for you.
If you do have the above legs then there would be no reason to purchase a new system assuming the old one is in working order. You will have a fresh set of gears and wired remote if you replaced the whole system but the installation will be much more involved and the cost will be much higher assuming you replaced both jacks. You will also need part # BD500389 if your trailer has an aluminum frame.
I have attached an install/review video on the above conversion kit for you as well.
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: redarc
- Shop: Suspension Enhancement
- Search Results: trailer hitch ball mount
- Shop: Gooseneck Hitch
- Shop: Brake Mounting Hardware Kit for 7" and 10" Brake Assemblies
- Search Results: sumosprings rear
- Shop: Brake Controller
- Shop: Vehicle Tow Bar Wiring
- Shop: Base Plate for Tow Bar
- Search Results: microair
- Shop: Kenda Karrier S-Trail ST145/R12 Radial Tire w/ 12" White Spoke Wheel - 5 on 4-1/2 - LR D
- Shop: Redarc Tow-Pro Link Bluetooth Brake Controller - Off-Road Mode - 4 Axles - Proportional
- Search Results: rv vents and fans
- Search Results: ram jack 12000
- Search Results: lg142178
- Shop: Demco Tabless Base Plate Kit - Removable Arms
- Shop: Blue Ox 4-Diode Universal Tail Light Wiring Kit for Towed Vehicles
- Shop: Blue Ox 7-Wire to 6-Wire, Coiled Electrical Cord
- Shop: Roadmaster Smart Diode Kit for Variable Voltage LED Tail Lights - 7-Way to 6-Way Adapter Cord
- Q&A: Brake Assembly Replacement Recommendation for Dexter Assemblies 36-19-47
- Video: Complete Breakdown of the Dexter Nev-R-Adjust Electric Trailer Brake Assembly
- Video: Detailed Breakdown of the Bug Screen for Dometic RV Refrigerator Sidewall Vents
- Video: Install: Air Lift Load Controller II Compressor System for Air Helper Springs on a 2013 Ford F-150
- Video: Feature Review Deluxe Window Frame for RV Entry Doors
- Q&A: Taillight Replacement Option For a Winnebago 170778-01-000 Light
- Shop: Trailer Hitch
- Shop: Front Mount Hitch
- Q&A: How To Wire Up a Pair of Bulldog Velocity Jacks part # BD185400
- Q&A: Wireless Remote Control for Bulldog Velocity Series Landing Gear Jacks
- Video: Complete Breakdown of the Timbren Axle-Less Trailer Suspension w/ Idler Hubs


Nico
5/29/2018
Thank you very much for your help. So I have a RAM landing gear. For the Velocity series will I need the adapter still? I saw you also carry a RAM Electric motor. Will that work for my application. Thanks again. Oh, I was also looking at purchasing a BX1 GN coupler. Will that work for my trailer or is that specific to Bulldog as well.