What is the Capacity of Gooseneck Coupler Head Kit, # GC-HEAD

Question

Question:

What is the weight rating of P/N GC-HEAD?

asked by: Evan

0

Expert Reply:

The Gooseneck Coupler Head Kit, # GC-HEAD, was designed for use with GCPN Series, GCSQ Series, and GCSQTW Series couplers which range in capacity from 25,000 to 30,000 pounds. So the maximum would be 30,000 pounds.

expert reply by: Michael H

0

Answer 1

I reached out to the company that builds the Ram Gooseneck Coupler item #GCSQTW-30008 , Pacific Rim International Factory, and was not able to get an exploded parts diagram. I have listed all of the replacement parts below that are available.…

view full answer...

Answer 2

Yes, the Gooseneck Coupler Head Kit part #GC-HEAD replaces the coupler head on etrailer.com or Ram, round and square Gooseneck couplers. It is designed for use with GCPN Series, GCSQ Series, and GCSQTW Series couplers which all have the 4" inner…

view full answer...

Answer 3

The center bushing on the Dexter Equalizer for 3" Slipper Springs #13-108-3 can indeed be replaced if/when it's worn. You do not need to replace the entire equalizer. The correct replacement bushing for this particular unit is the part…

view full answer...

Answer 4

The correct replacement leaf spring bushings for any given trailer will be dependent on the width and type of the leaf springs. The most common for a Dexter 10,000 lb Trailer Axle are 3" wide slipper springs. If you have 3" wide slipper…

view full answer...

Answer 5

According to the manufacturer the Gooseneck Coupler Head Kit #GC-HEAD is made from mild cast steel.

view full answer...

Answer 6

We have the bushing that you are looking for! It is #14-69. It has a 1 inch inner diameter, 2 inch outer diameter, and it is 3 inches long. It is designed for Dexter 10 to 15K axles.

view full answer...

Answer 7

The Bulldog Coupler Repair Kit BD0287740300 is designed for a round coupler so if you have a square tube you'll have better luck with the Gooseneck Coupler Head Kit #GC-HEAD. This is designed around etrailer and RAM round and square gooseneck…

view full answer...

Answer 8

The Gooseneck Coupler Head Kit #GC-HEAD has a shipping weight of 13-lbs.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

What is the Capacity of Gooseneck Coupler Head Kit, # GC-HEAD

Product Page this Question was Asked From

Continue Researching