Recommended Ball Mount for 2 Inch Ball with No Rise and No Drop

Question

Question:

The product I need is evidently not provided by your current suppliers. I know it was made a one time because I have one but would like to have another.

asked by: Ed R

0

Expert Reply:

For a 2 inch hitch ball that has no rise and no drop, I recommend the Curt Solid 2-Ball Mount for 2" Hitches - 2" and 2-5/16" Balls - 10K - Black # C45660. For your anti-rattle, I recommend the Roadmaster Quiet Hitch for 2" Trailer Hitches # RM-061 which will give you the anti-rattle and then # e98880 for a locking hitch pin. If you want a 3 ball option I recommend # C62KR.

expert reply by: Jason S

0

Ed R.

10/20/2017

The product I need is evidently not provided by your current suppliers. I know it was made a one time because I have one but would like to have another.

Reply

Jason S.

10/20/2017

The only thing that I can think of that you may have is the Convert-A-Ball Cushioned Multi-Hitch Clevis and Pintle Hook Combo w/ 3 Balls - 2" Hitches - 10K # CAB-6W. This isn't technically an anti-rattle but it will reduce noise and vibration. It has a polyurethane interior that acts as a shock absorber to reduce bounce and rhythmic vibration. The pintle hook combo # PH2 also has this shock absorber cushion.

Reply

Answer 1

The only trailer hitch ball we offer with a 1-3/8" diameter shank is the Hitch Ball part #BWHB94007 which has a 2-5/16" ball diameter and 30,000 lb weight capacity.

view full answer...

Answer 2

The Roadmaster Spare Tire Carrier #RM-195125 is going to likely be your best option. The only other option would be a Carrier #e98ZR you would have to remove to open the door. I have added an image with the length of the carrier below as you may…

view full answer...

Answer 3

In order to lock-out the turret on a Reese Sidewinder 5th Wheel King Pin like part #RP34FR you will need to use two grade eight 3/4"-10 x 9" hex bolts and the corresponding lock nuts and washer. Unfortunately, we do not carry this size bolt…

view full answer...

Answer 4

We don't sell the 3/4 x 5-1/2 inch grade 5 bolts needed to lock out a Sidewinder. The only way you will be able to get the correct bolts would be to go to your local hardware store and get them there. This will save you time as you won't have…

view full answer...

Answer 5

Hey Chaz, yes the Reese ball mount part #RP82AR that you referenced can be used in the rise position. The torque rating for the ball's nut will be based on the hitch ball that you use and not the ball mount.

view full answer...

Answer 6

The Roadmaster Spare Tire Carrier #RM-195125 pivots to the side as opposed to folding down so the height when doing that would only be to the top of the bracket, which is 7-1/2 inches. When it is in the upright position, the overall height will of…

view full answer...

Answer 7

The Roadmaster Spare Tire Carrier #RM-195125 is going to have a height of 24" from the center of the receiver to the center of the spare tire mount.

view full answer...

Answer 8

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Recommended Ball Mount for 2 Inch Ball with No Rise and No Drop

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching