Torque Specs for Nuts that Come with 1-1/2" Square Trailer U-Bolts # SP01-120

Question

Question:

Hi, I had bought these parts. The U-bolt 1 1/2inch W/nuts 2 Pack part #SP01-120 and U-bolt Plate - 1-1/2inch Square Axles W/1-3/4inch Wide Springs part #115983. Do you know what the specified torque is for the U-boat nuts?

asked by: Michael C

0

Expert Reply:

Yes, my contact at Redline said the nuts that come with the 1-1/2" Square Trailer U-Bolts # SP01-120 should be torqued anywhere between 45-75 ft-lbs.

expert reply by: Jon G

0

Answer 1

If the U-bolts are 9/16 inch diameter, the torque specs should be between 65 to 95 foot lbs. If the U-bolts are 3/8 inch diameter, the torque should be between 30 and 50 foot lbs.

view full answer...

Answer 2

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 3

The torque rating for the 1/2 inch diameter u-bolts in the U-Bolt Kit #APUBR-1 is a minimum of 45 ft lbs and a maximum of 70 ft lbs. These are designed to mount your trailer's leaf springs to round, 2-3/8 inch diameter axles. The U-bolts, plates…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Torque Specs for Nuts that Come with 1-1/2" Square Trailer U-Bolts # SP01-120

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching