Best Grease to be Used with Bearing Buddies

Question

Question:

Hi is the l10320 the best grease for my r v travel trailer 2 axle trailer and about 6500 lbs and does if work with other greases can I use this with buddy bearing please let me know thanks Irv

asked by: Irv M

1

Helpful Expert Reply:

According to Bearing Buddy the best grease to use is a high quality, multipurpose # 2 grade lubricant. They also recommend not mixing different types of grease.

I recommend using LubriMatic # L11465.

expert reply by: Charles S

1

Answer 1

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 2

I was able to find some information on your Cargomate TXLEEH58SA trailer. From what I found, it appears your tire size is 15 and your load range is B based on the factory tires. We have only have a load range C option and it is the Loadstar…

view full answer...

Answer 3

Ideally you want bunk boards that are at least 50% of the length of your boat, and want the to run from the stern and as far forward as you like. Since your boat is 16' Long you will want at least 8' of bunk boards, but I recommend going with…

view full answer...

Answer 4

I have a solution for you but I'm not aware of a bolt on safety chain bracket or clevis. However you can simply take a safety chain set like the 42" Long Safety Chain with 3/8" Clevis Hook (15,000 lbs) #337BSC3842 and use a grade 8 bolt…

view full answer...

Answer 5

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 6

Hey Ben, yes you can use the Truxedo Boat Windshield Cover part #TX38FR on a windshield that is taller than 25 inches and it will still work. How much taller is yours though?

view full answer...

Answer 7

The 910 lb rating indicates that this is a load range C tire. The maximum PSI for a tire like this is 75 PSI. For Example the Kenda 5.70-8 #AM30120 have a ply rating of 6 and a 910 lb max load at 75 PSI. Also, each tire should have the PSI specified…

view full answer...

Answer 8

In terms of speed rating the Goodyear Endurance ST205/75R14 Radial Trailer Tire is certainly superior to the Kenda Karrier #AM10235, as it features an 87 mph maximum speed (compared to 81 mph on the Kenda). Based on your question, where it seems like…

view full answer...

Answer 9

We do have Bearing Buddys with threads on them, but you'll need to verify fitment on your end: Stainless Steel - #BB1980T-SS fits a 1.980" hub bore Stainless Steel - #BB2080T-SS fits a 2.080" hub bore Stainless Steel - #BB2441T-SS fits…

view full answer...

Answer 10

You actually don't have to use a thread sealant with the Bearing Buddies like the part #BB2080T-SS like what you mentioned.

view full answer...

Answer 11

An EZ lube spindle will be better because it allows you to insert grease from inside the spindle where the bearings are and push out the old grease whereas with a Bearing Buddy you basically just get to push grease through the front of the hub. I…

view full answer...

Answer 12

Yes you can use a Bearing Buddy on your current axle setup but you'll have to remove the zerk/grease fitting. What you have now is an EZ lube spindle which allows you to push grease through the middle of the spindle but you can install a Bearing…

view full answer...

Best Grease to be Used with Bearing Buddies

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching