Mounting Hole Spacing on Trailer Fender Brackets

Question

Question:

Whats the distance between the two bolt holes on each arm of the L bracket?

asked by: Bart

0

Expert Reply:

On the shorter arm of # CE26098G-2, the two holes from center-to-center are going to measure 4 inches. On the longer arm, from center-to-center, the holes are going to measure 2-3/8 of an inch. And the hole diameter is 3/8 of an inch.

expert reply by: Charles S

0

Answer 1

Hey Ed, You can switch to larger tires but you would potentially need to move the fenders up to keep a minimum of 3" of clearance so that the wheels won't rub as the suspension compresses. Are you looking to just replace the tires and keep…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 11

Thanks for the pics Kemo, they really helped! The CE Smith Single Axle Trailer Fenders #CE19504-2 are larger than what you currently have and use a different mounting style. Based on your setup, the CE Smith Fenders wouldn’t bolt onto your existing…

view full answer...

Answer 12

Hi Keith! The Tie Down Plastic Fender for 13" to 15" Wheels - Black #TD86VR is sold as a single fender, so you would need to order a quantity of two if you are wanting one for each side. The closest we have that is a pair would be the CE…

view full answer...

Mounting Hole Spacing on Trailer Fender Brackets

Product Page this Question was Asked From

Continue Researching