Replacement Lens Recommendation for LED Trailer Light STL37RB

Question

Question:

looking for a replacement lens for the Over 80, Aero Pro Submersible LED Trailer Tail and License Light, 8-Function, 23 Diode, LH Optronics Trailer Lights left hand side

asked by: Greg

0

Expert Reply:

We don't have an exact replacement for the # STL37RB but we do have a replacement lens for the incandescent version of this light. For that you would need the part # A39RB.

expert reply by: Jameson C

0

Answer 1

The trailer taillights part #STL16RB and #STL17RB have 18 diodes and the tailligths part numbers #STL36RB and #STL37RB have 17 diodes so they are very similar.

view full answer...

Answer 2

I don't have any reference to the "S2T216AP2 " that you provided but based on my research it sounds like you might have the Optronics LED Combination Trailer Tail Lights part #TLL160RK. If that is the case then the correct replacement…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Replacement Lens Recommendation for LED Trailer Light STL37RB

Product Page this Question was Asked From

Continue Researching