Would the Replacement Square End Cap 853-5826 Fit Gorilla Lift GL1

Question

Question:

Trying to find end caps that will fit on the end of Gorilla lift trailer aid. OD is 2x2 ID is 1.75 will this 2x2 plug work. Thank you

asked by: Harley

1

Helpful Expert Reply:

The Replacement Square End Cap # 853-5826 should work perfectly for you. I went out and measured one and found that it's overall diameter is 2 inch by 2 inch and the inner tube piece measures a tiny bit over 1.75 inches by 1.75 inches so it would fit your trailer that has an inner tube of 1.75 inches as well.

expert reply by: Jameson C

1

Answer 1

According to the instructions for the Gorilla-Lift Utility Trailer Tailgate Lift Assist part #GL1, you must cut the big outer spring to remove the small inner spring. I have attached an excerpt from the instruction manual below which states this. I…

view full answer...

Answer 2

I attached a page from the install instructions for your Gorilla Lift Tailgate Assist #GL1 that covers how to lower the spring tension.

view full answer...

Answer 3

The Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable #GL1 would still work even if it was placed further back, but with a 3' gap you'd likely need to get a longer cable from your local hardware store to bridge the gap. If not the…

view full answer...

Answer 4

To replace your GloBrite 126 marker lights you can use the #MC44RB for the red light and the #MC44AB for the amber light. Both of these lights are 2 wire lights and will work well on your cargo trailer. And yes, we can ship this particular product to…

view full answer...

Answer 5

Glo Brite is indeed out of business, but we may have an amber LED assembly that will work nicely as a replacement to your broken unit. The closest LED assembly we have available to the measurements you provided is with the Command LED Clearance or…

view full answer...

Answer 6

I may have a solution for you, but Glo-Brite has since gone out of business, so replacement lenses that are guaranteed to fit are no longer available. With that said it certainly looks like your Glo-Brite 126y is very similar in shape and size…

view full answer...

Answer 7

To replace your GloBrite 126 marker lights you can use the #MC44RB. These lights are 2-wire incandescent lights measuring 4" long by 1-1/2" wide (same as your existing marker lights) and will work great for your trailer.

view full answer...

Answer 8

Since your gate is under 300 lbs I recommend using the Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable #GL1. This is rated for 300 lbs and is compatible with open utility trailers that have square-tube, round-tube, or angle-iron side…

view full answer...

Answer 9

The best trailer tailgate/ramp assist we have for your Bix Tex 70TV Trailer is the Gorilla-Lift Utility Trailer Tailgate Lift Assist part #GL1. That said, this lift assist is only designed for a max side rail height of 24" which is also the max…

view full answer...

Answer 10

Since you've already set the first Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable #GL1 to the desired tension to lift the gate alone you may have to redo the placement of your original gate bolt to set the tension correctly for both…

view full answer...

Answer 11

Don, it looks like the Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable #GL1 is only going to work with trailers that have a side wall height from 12" to 24" so with yours being so short, it's not going to work unfortunately.…

view full answer...

Answer 12

We have installed the Gorilla-Lift Utility Trailer Tailgate Lift Assist #GL1 on similar trailers to your Gorilla 10' trailer with a 2' dovetail. I have included an image below of a similarly designed trailer which has a taller gate. The…

view full answer...

Would the Replacement Square End Cap 853-5826 Fit Gorilla Lift GL1

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching