What Is Backspacing Dimension For Taskmaster Steel Dual Trailer Wheel

Question

Question:

Whats the total back spacing on the wheels

asked by: Edward N

0

Expert Reply:

The total backspacing for the Taskmaster Steel Dual Trailer Wheel, part # TTW660865SDX2C is 8.85 inches front he front of the mounting surface to the back of the rim on the wheel.

This is a 16-inch x 6-inch wheel with an 8on 6-1/2 bolt pattern. The wheel has a 4.88 inch diameter pilot and has a 3,500-lb capacity.

expert reply by: Jeffrey L

0

Answer 1

Most trailer wheels have a zero offset. This is because a zero offset allows the wheel to handle the maximum load by distributing the the load equally to both sides of the wheel. To determine if your trailer wheels have an offset, you will want to…

view full answer...

Answer 2

Most trailer wheels have a zero offset. This is because a zero offset allows the wheel to handle the maximum load by distributing the the load equally to both sides of the wheel. To determine if your trailer wheels have an offset, you will want to…

view full answer...

Answer 3

Wheel offset is very similar to backspacing and refers to the location of a wheel's rim in relation to the wheel's center. Most trailer wheels have a 0 offset, but to determine if the wheels on your trailer have one, you will first want to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

What Is Backspacing Dimension For Taskmaster Steel Dual Trailer Wheel

Product Page this Question was Asked From

Continue Researching