Dimensions and Hole Spacing of Draw-Tite 41954 Class V Hitch

Question

Question:

Do you have measurements for this hitch?

asked by: Sarah

0

Expert Reply:

The Draw-Tite 41954 Class V hitch which we offer as part # DT35MR is designed for 2015 - 2022 Ford F-150 models that aren't equipped with a factory hitch.

I've made up a diagram showing the dimensions and hole spacing for you.

expert reply by: Mike L

0

Dimensions of Draw-Tite DT35MR Hitch
(click to enlarge)

Answer 1

Hey Wayne! The answer to your question is maybe. As you know, the Curt #C14017 is designed for the F-150 without the factory hitch. Typically this is because the factory hitch is integrated with the bumper and removing it to replace it with the…

view full answer...

Answer 2

The big differences between a Class IV and a Class V hitch are the capacities and the opening size. Class IV is going to be a 2 inch hitch opening that has tongue weights typically up to 1,200 lbs and total trailer weight of 12,000 lbs. For a Class V…

view full answer...

Answer 3

While locking hitch pins aren't rated for capacity like a hitch, the strongest is the InfiniteRule hitch pin, which has a 42,000 lb shear strength. They are available for 2", 2-1/2" and 3" hitches: - 2" Hitch: InfiniteRule…

view full answer...

Answer 4

Sometimes hitches can get slightly bent during shipping and this can be fixed by bending the hitch back into place as long as the hitch only has a slight bend to it. If yours isn't lining up I can almost guarantee that is what happened. Some…

view full answer...

Answer 5

Yes, we do Jay! It is the Replacement Hardware Kit for Trailer Hitches item #RHK. This will have all of the hardware you need to install the Curt Hitch item #C14017, you were looking at. You will want to go to the item #RHK product page and on the…

view full answer...

Answer 6

As the Draw-Tite #DT35MR Class V hitch is designed to fit a 2018 Ford F-150 that did not come with a factory hitch, I will have to steer you in a different direction. With that said, the Curt Class IV Hitch #C26HR will fit trucks that came with the…

view full answer...

Answer 7

To add a 7-way to your 2023 Ford F-150 that already has a 4-way, all you need is the following: - Universal Installation Kit for Trailer Brake Controller #ETBC7 This will give you the 7-way, wiring, circuit breakers, and rest of the hardware needed…

view full answer...

Answer 8

While we do have a hitch option for your 2018 Ford F-150, you won't be able to use the Draw-Tite Ultra Frame Trailer Hitch Receiver - Custom Fit - Class V - 2" #DT35MR. This is because the Draw-Tite is designed for truck frames styles of…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Dimensions and Hole Spacing of Draw-Tite 41954 Class V Hitch

Featured Help Information

Miscellaneous Media

Continue Researching