How Much of a Slipper Spring Should be Sticking Out Past the Rear Hanger
Updated 07/14/2016 | Published 07/13/2016 >
Question:
How far should should the flat end of a 30 1/4 spring extend beyond the ring with no load on it the frame is upside down now
asked by: Mike D
Expert Reply:
The flat end of a slipper spring should stick far enough through a hanger to allow for the full travel of the suspension without the spring coming out of the hanger. When you have no load on the spring and especially if the frame is currently upside down then the end of the spring will likely be very close to the hanger. Once it is right side up the spring will compress some and push more of the flat end through the hanger.
With spring # SP-039275 the hanger spacing should be 28 inches measured from the center of the front hanger to the center of the rear hanger so that is another way to make sure the spring is in the right place.
Continue Researching
- Search Results: stl~79rb
- Search Results: door seal
- Search Results: jaguar
- Search Results: e5115 spring
- Search Results: curt 51146
- Search Results: 023~340~00
- Search Results: stl~9rb
- Video: Review of Terran Industries Trailer Leaf Springs - 5 Leaf Slipper Hook Spring 3.5K Axle - TX93RJ
- Video: In-Depth Look at the B&W 5th Wheel to Gooseneck Pin Box
- Shop: Trimax Super-Max Universal Trailer Coupler Lock - 1-7/8", 2", and 2-5/16" Couplers
- Shop: Peterson LumenX LED Tail Light - Stop/Turn/Tail/Backup - 7 Diodes - Oval - Red/Clear Lens - 5 Wire
- Shop: Dexter Hydraulic Trailer Brake - Free Backing - 12" - Left Hand Assembly - 7K
- Shop: Square 2-Speed Trailer Jack - Drop Leg - Sidewind - 12-3/8" Lift - 10,000 lbs - Weld
- Shop: Square 2-Speed Trailer Jack - Drop Leg - Sidewind - 12-3/8" Lift - 10,000 lbs - Weld
- Shop: 7-Leaf Slipper Spring w/ Hook End for 8,000-lb Trailer Axles - 26-5/8" Long
- Shop: Rear Hanger for 2" Wide Slipper Springs - 5-1/16" Tall - 9/16" Bolt Hole
- Q&A: Solution for Replacement Aluminum Jaguar Trailer Wheel in Black
- Video: Spring-Eye Bolt with Locknut for Slipper Springs: The Breakdown
- Video: Hands-On with the CE Smith Replacement U-Bolt w/ Nuts for 2-3/8" Round Axles
- Video: Feature Breakdown: U-Bolt Plate
- Video: Review of Demco Straight Tongue Trailer Coupler - Bolt On eZ-Latch 2 Inch Ball Silver - DM15000-52
- Video: Review of Demco Straight Tongue Trailer Coupler - Tube Mount Coupler - DM12563
- Q&A: Are Radius End And Flat End Slipper Springs For A Trailer Interchangeable?
- Q&A: Can I Use Heavier Rated Leaf Springs on Trailer Without Causing Damage
- Q&A: Picking Out Trailer Leaf Springs for Trailer with 30 inches between Hangers
- Q&A: What is the Spacing Between the Front Hanger and Rear Hanger for 27" Leaf Spring Single Axle Trailer
- Q&A: Correct Slipper Spring for my 16 ft. Aluminum Jon Boat Trailer
- Q&A: Recommended Slipper Spring for Custom Kayak Trailer
- Article: Slipper Spring Trailer Suspension System Review
- Article: How to Measure a Trailer Axle
