What If I Exceed Weight Limit of Class 3 Hitch

Question

Question:

What is the weak link if I put my 7 thousand pound trailer on this challenger. Will the frame of the car bend? I will be using an equalizer hitch.

asked by: Larry S

0

Expert Reply:

Exceeding the weight rating of the vehicle or hitch could cause engine damage, transmission damage, hitch failure and the hitch could rip out of the frame of the vehicle.

The important thing to remember is that the Curt trailer hitch # 13465 is rated for 3,500 pounds. If the vehicle is rated lower you go by the lower rating. You would not want to go beyond the capacity specified in your vehicle owners manual.

I cannot recommend using this hitch with an Equalizer hitch since it is not rated for use with weight distribution systems.

I have included a link to a video showing a typical installation for you.

expert reply by: Chris O

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

OEM brake controllers integrate into the dash display of the vehicle which is why they require programming whereas aftermarket brake controllers like the Tekonsha #90885 do not at all so they don't require it. All you need to install this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

For the Draw-Tite Max-Frame Trailer Hitch item #76145 you are going to want the Curt Towing Starter Kit for 2" Hitches item #C45534. This towing kit will provide you with a 2" ball and a fixed ball mount with a 3/4" rise and 2"…

view full answer...

Answer 10

I have a solution for you but the Curt Trailer Hitch item #13465 will not give you enough clearance to mount the Kuat Sherpa 2.0 Bike Rack for 2 Bikes item #SH22B. The hitch pin hole sits too far underneath your car when installed. Instead you will…

view full answer...

Answer 11

I will be happy to explain how to install the shock kit #LC281281. In addition to the instructions below I have also included a picture of the actual instructions. 1. Raise trailer and jack up the axle to release pressure on the springs. 2. Remove…

view full answer...

Answer 12

Hey Mike, yes we have replacement hardware for all of the hitches we carry including the part #13465 with the part #RHK. You'd just need to enter the part number for the hitch on the product page and we'll ship you out the correct hardware.

view full answer...

What If I Exceed Weight Limit of Class 3 Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching