Dexter Predator DX2 Trailer Brake Controller - 1 to 2 Axles - Proportional
Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long
Part Numbers: 58-8,20127
Retail:$240.60
Our Price: $178.33
You Save: $62.27
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Dexter Predator DX2 Trailer Brake Controller - 1 to 2 Axles - Proportional
part number: 58-8
This proportional brake controller keeps it simple with intuitive controls that are easy to use. Includes a large digital LED display, fingertip gain control, a slide-bar manual override, and built-in safety features.
Features:
- Brake controller activates your trailer brakes in proportion to your vehicle's braking action
- Automatically adjusts trailer's braking based on deceleration of tow vehicle
- Large digital LED display shows your controller settings and monitors voltage output
- Simple, intuitive controls keep your settings in easy reach
- Adjustable gain setting determines the amount of braking output sent to the trailer's brakes
- Built-in, slide-bar manual override activates trailer brakes to control sway in emergency situations
- Deceleration sensor lever lets you adjust initial braking power and aggressiveness for smooth, safe braking
- Built-in safeguards protect your vehicle and trailer
- Current limiter protects vehicle from shorts in the trailer wiring
- Hazard flasher immunity prevents pulsing of the brakes when flashers are activated
- Quick and easy mounting with included bracket and hardware
- 90 To -35 degree mounting range - must be horizontally level
- Pigtail harness hardwires into your vehicle
- Made in the USA
Specs:
- Application: trailers with up to 2 axles (4 brake assemblies)
- Compatible with electric brakes only
- Dimensions: 6-1/2" long x 3" wide x 1-5/8" tall
- Mounting angle: -35 degrees to 90 degrees vertically
- 7-Year limited warranty
Proportional Braking
The Dexter Predator DX2 brake controller comes equipped with proportional braking to give you the best towing experience. Proportional braking means that your trailer brakes mimic your tow vehicle's brakes. If you slam on the brakes in your vehicle, your trailer brakes will activate with the same intensity; if you brake lightly, your trailer brakes lightly too. The trailer's braking is in proportion to your vehicle's braking. This saves wear and tear on the tires and the brakes on both your vehicle and trailer.
The Predator DX2 uses an internal 3-axis accelerometer to sense how your vehicle is braking so it can send the right amount of braking power to your trailer. It measures the inertia of your tow vehicle and activates the trailer's brakes to slow at the same rate. The result is uniform braking across your towing setup. No push-pull action - just smooth, proportional braking every time.
Large Digital LED Display
The Dexter Predator DX2 features a large LED display that's easy to see so you can check on your current braking output setting with a glance. This display is designed to keep it simple and not overload you with information. The display will also show you the voltage to confirm that the trailer brakes are receiving power.
Braking Output
During the initial setup process, use the thumbwheel on the front of the brake controller to adjust the braking output. The output control lets you set the maximum amount of power that will be applied to your trailer's brakes. Typically, the output is only readjusted when you experience changing road conditions or if the weight of your trailer changes. The power output control on this brake controller lets you set the maximum amount of power that will be applied to your trailer's brakes. Typically, the power output is only readjusted if you switch from a heavy, loaded trailer to a much lighter, empty trailer - or vice versa.
During the initial setup process, you can use the thumbwheel to adjust the power output. To get more power to your brakes, increase the power level. To decrease the power output, lower the power level.
Sensitivity Adjustment with Deceleration Sensor Lever
Once you have the overall power set, you can fine-tune the power output by adjusting the sensitivity of the internal sensor. This controls the aggressiveness of your trailer's braking, meaning how quickly the brakes reach the maximum braking level. You can adjust this when you're towing heavy loads and you need more umph to bring your trailer to a stop. Your tow vehicle doesn't need that much power to brake in time, but your heavy trailer does. Boost gets the braking power to your trailer brakes faster and with more intensity so that it doesn't push your tow vehicle forward. To increase the sensitivity for towing heavier loads, move the lever away from you. For a lighter load, move the lever toward you.
Slide-Bar Manual Override
The Dexter Predator DX2 comes with a built-in manual override slide-bar in easy reach, great for stopping sway or controlling your trailer's momentum in emergencies. To engage the manual override, just push the slide-bar to the left. This will activate the trailer's brakes and brake lights without you having to apply the brakes on your tow vehicle, perfect for limiting trailer movement while you're cruising.
You can also engage the manual override to help you move a sliding 5th-wheel hitch closer to your truck's tailgate for tight maneuvering during slow speed turns. Just apply the manual override to hold the trailer in place while slowly moving the tow vehicle forward.
Quick, Simple Installation
Because the controller operates with an internal inertia sensor, it must be mounted between -35 degrees and 90 degrees vertically. The Predator DX2 also needs to be horizontally level and parallel with the direction of travel to function properly. During initial installation, the deceleration sensor lever must be positioned straight up and down. After mounting the Predator DX2 using the included bracket, hardwire the controller directly into your vehicle.
Installation Accessories
See etrailer.com's exclusive 7- and 4-way brake-control installation kit (ETBC7 - sold separately) if you don't already have a 7-way plug at the back of your vehicle
Note: One of the following will be required to ensure proper installation:
- 20-Amp circuit breaker (9506P - sold separately) for 2- to 4-brake applications
- 30-Amp circuit breaker (38630 - sold separately) for 6- to 8-brake applications
058-008-00 Dexter Predator DX2 Electric Brake Controller with Inertia Sensor - 1 to 2 Axles - Proportional
Replaces 58-8
Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long
part number: 20127
Tow Ready Replacement Plugin Harness for the Tekonsha P3, Voyager, Prodigy, and Primus Brake Controllers. Also works with Draw-Tite Intella-stop Xtreme, Intella-stop Ultra, Intella-stop Digital, and Activator III (5520) brake controllers.
- Wire lead length: 12"
- Wire functions:
- Blue: trailer brakes
- White: vehicle battery negative terminal
- Black: vehicle battery positive terminal
- Red: cold side of stoplight switch
8506920 Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long
Replaces 20127
California residents: click here
Customer Satisfaction Score:
94% were satisfied with this product
6% of customers were not satisfied
- Wrong item was ordered
- Defective
- Product did not meet expectations
Customer Reviews
Dexter Predator DX2 Trailer Brake Controller - 1 to 2 Axles - Proportional - 58-8
Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long - 20127
Average Customer Rating: 4.8 out of 5 stars (735 Customer Reviews)
This proportional brake controller keeps it simple with intuitive controls that are easy to use. Includes a large digital LED display, fingertip gain control, a slide-bar manual override, and built-in safety features.by: Michael 02/18/2023
Exactly what I was looking for and needed ! It was delivered very quick . Actually I just ordered a complete wiring harness from you tonight . Your service and follow up is great
by: David11/05/2019
2007 Ford Ranger
Purchased a Teckonsha Voyager brake controller and the ETBC7 install kit.
The instruction an video were very clear and easy to follow. Installed on a 2007 Ford Ranger Sport. Tech support was also very helpful on the one question I did have.
David
11/8/2020
I have been completely satisfied with this item. It has operated as advertised an has had no problems.
by: Wayne12/20/2019
The drawtite hitch and trailer wiring harness fit great. Instructions were clear and concise. Installation was a breeze. I am ready to tow my little trailer now. As soon as I get the brake controller installed, I will be ready for my big trailer.
by: Chris C10/09/2016
If your truck comes with the tow haul package.... this item is literally plug and play. I had it wired up and all mounted inside of thirty minutes. It's literally 4 wires and the stock system wires are labeled along with the brake contoller. I haven't tested it yet but so far I am thoroughly impressed!
by: Griff Morgan06/19/2022
Class iii Draw Tite trailer hitch:
This part was quick and easy to order and I received it sooner than expected. My mechanic said the installation was easily accomplished and looks great on my car. I would not hesitate to order from etrailer again!
Griff M.
6/21/2023
The product has worked well. I have had no problems with it.
by: Rudy04/20/2023
Purchased this as part of all parts required to convert 1996 Jayco over to electric brakes. Very happy with results. Surprised to see after winter in storage that the battery supply still shows full charge.
by: Easy install01/21/2021
Perfectly wired directly to existing wiring that I had for the previous brake controller I replaced with the, Draw Tite I Command. This will make it a lot easier should I choose to upgrade the unit in the future.
Fantastic customer service from Joshua as well.
by: Bryce05/03/2022
Ram 2500
I installed the Curt gooseneck on my 1993 GMC 2 Wheel Dr. 2500 truck. All the components have tight tolerances. It took me eight hours. With a socket and the wrench. Laying on my back. I did have to cut the wheel well lip about 3/8 of an inch off because I could not get that front angle bar to slide in without hitting it, no way around it unless you lift the bed up and I wasn’t going to do that!!. You have to cut it.instructions do not state that. I’m very happy with the Hitch, it is definitely stout! I did have to make a notch on the outside brackets to go over my airbag bolt. I also had to remove the support bracket on the inside of the frame for the airbag and the crossmember for the spare tire to get the front angled bar in.
by: Douglas08/03/2023
As always, etrailer delivers. Part was on time and a perfect match for the brake controller. What you don't get from Amazon is the technical support on how to install or use the equipment purchased from etrailer. That's why I keep coming back!
by: Rancher01/07/2023
Finally a brake controller that does what I set it to, not what it’s little computer brain, designed by someone who has never pulled a trailer thinks it needs to do.
by: Don 03/07/2021
My truck was stolen and wrecked. I was able to retrieve the Tekonsha Brake controller from under the Dash board before it was hauled to the salvage yard, but not the wire harness. I was ale to order a replacement harness from eTrailer and reinstall the controller in my new truck. I had no problems at all. Thank you eTrailer for the great support.
Don
3/9/2022
Still works perfectly after one year. Actually, I been using this Controller for well over a year. I just reinstalled it in my new truck a year ago.
by: Tim 06/21/2020
These guys are great they had the installation kit it came with everything you need and even had a video for my specific vehicle to install the brake controller and wire in a 7 pin trailer plug
If you don’t have factory brake controller the etbc7 is an amazing kit they have comes with everything I mean everything
Tim
6/26/2021
Everything has been excellent e trail has the right products and they fit just like they say
by: Charles 09/25/2022
Chevrolet
Wiring harness I used to connect into the trailer brake control circuit. Requires pulling some inside trim in the drivers footwell area to access my 2022 Chevy Colorado's wires. Follow the intructions or better yet go onto YouTube for video on what goes where.
by: Chad07/13/2021
Works as intended, but the plug on the back of the controller is a loose connection. Sometimes I would go to brake and find that I had no trailer brakes because the controller lost power. After a wiggle it would start to work again. I was able to shave the Molex plug a bit and now I don't have any problems with it.
Sierra K.
7/19/2021
Thank you for your review. I have not heard of that problem. I would have used some electrical tape.
by: Michael 09/22/2022
I installed this controller in my 1982 Chevy K20 pickup.
It works perfectly! Etrailer exceeded my expectations with their level of customer service from the time the order was placed to the products arrival at my home. Truly 5-star service!
The video tutorials are straight forward and very helpful.
The universal installation kit literally had everything needed to complete the job.
Side note:
I would have liked to see the (2) 10ga wires in the insulation to be black and blue, not black and white, no biggie, black on black and white on blue.
Thanks again!
by: Bill08/13/2020
The service you receive from etrailer is top notch. This brake controller has worked very well. I actually swap it between two of our vehicles. Just unplug it from one and plug it into the other.
Bill D.
8/15/2021
Very well. The service etrailer provides is the highest Ive ever experienced. They are just super to work with. Ive used them time & time again. I recommend them to everyone looking for anything they carry.
by: Shad11/01/2022
Works great. FYI YOU HAVE TO RUN A BRAKE WIRE FROM THE CONTROLLER TO YOUR LIGHT PLUG . For it to work properly.
by: Steve03/10/2024
1976 Chevrolet Blazer
Great selection and servive
by: Mile03/19/2024
Quality plug and what i needed for my F-53 chassis.
by: Bernard05/16/2023
The controller is on 24/ 7.I wish it turned on with the truck but this is more of a criticism of the truck not the controller I added a toggle switch so I can turn it off when I will not be using the trailer for a long spell.
by: Beck05/28/2022
One year later I'm extremely pleased with this purchase. I often chuckle when I see stock hitches and the whole thing is visible while mine is neatly tucked under with everything hidden except for the 2" receiver. 10/10 have recommended etrailer on many occasions to friends and family for their service and know-how. Since installing my hitch I towed a pop up camper 1500+kms and do frequent trips to the dump or my local dirt and gravel yard for supplies. Love it!
by: Steven05/03/2022
2008 Honda Pilot
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat, Item # ETBC7
I installed this 7-pin plug kit on my 2008 Jeep JKU to add power and trailer brake control.
I also purchased :
Draw-Tite I-Command Trailer Brake Controller Item # 5535
and
Curt No-Drill Bracket Item # C57202
along with a little extra wire, just in case.
The kit quality was great. It shipped with everything I needed, sans the controller and bracket above. I used a cordless drill, a quarter inch drive socket set, screwdrivers, wire cutter/crimper, pliers, black electrical tape, half inch loom (plastic flexible conduit) and quite a few extra zip-ties I had laying around. I needed the Curt bracket to mount the 7-pin plug farther away from the muffler that runs parallel to the bumper in Wranglers.
I first ran the grey jacketed wire from the rear bumper all the way to the engine compartment. This was the hard part for me since I'm old and a little more round than I'd like. I didn't need to raise the jeep since it already has a 2 1/2 inch lift. I zip-tied the jacketed wire to the frame and brake lines until I found a spot in the frame I could run it through. I ran it out of the frame at the rear of the left front wheel well and up into the engine compartment. There is a (very handy) rubber plug in the firewall just to the left (outboard) side of the brake vacuum booster. I made a small slit in the rubber plug. I removed the outer jacket from the wire at that spot and fed the white (future brake controller wire) into the cabin of the jeep. I ran the black wire, in a wire loom/conduit across the top of the firewall to the battery. I had enough extra wire to run the brake controller power and ground wire from the battery, across the top of the firewall in the same conduit, and into the cabin through the same rubber plug/grommet. I drilled small pilot holes to mount the two circuit breakers. I then connected the wires at the 7-pin plug at the rear bumper. I again made a pilot hole and then mounted the ground wire with the self-tapping screw provided in the kit.
Here I'd like to mention, I would have been happier with heat-shrink connectors. I could have gone to town and bought some, or I could have soldered the connections. Instead, I just used the provided connectors and a LOT of black tape. If I have any corrosion issues later I will replace the connectors provided in the kit.
I wired and mounted the brake controller. This would have been super easy if I could fit under the dash. I dislike using the little blue inline wire connectors (self stripping connectors) but it was a godsend when working one-handed under the dash. I mounted the controller bracket and covered most of the exposed wiring with black tape for aesthetics.
If I was 20 or 30 years younger, I would have had this whole kit installed in about 1 1/2 hours. I am very happy with the quality of the materials. Many others have already noted the bracket is not quite perfect where it is designed for the four wire plug to slip in. The four wire plug had moved slightly on my 20 minute drive to work and would likely have fallen out if I went much further. I may put a wrap of electrical tape around the plug to tighten up the fit. Otherwise I will see if a zip-tie or a drop of superglue will hold the four wire plug in place. I was a wee bit skeptical about the sturdiness of the no-drill bracket as it's held in place by what looks like a hose clamp. I am happy to report, the clamp is heavy duty and well made. The no-drill bracket with the 7-pin and 4-pin receptacles are very sturdy and secure. The instructional videos on etrailer's website made the job easy to understand.
If I had this job to do over again, I would definitely use the same products from etrailer.
by: Bob J.09/07/2016
I am very satisfied with the Dexter Axle Predator Electric Brake controller. I purchased the Dexter brake controller to be compatible with Dexter car trailer axles on a 16 foot car hauler. The braking unit is very useful when towing in very steep and winding mountain terrain. I feel that the braking is a necessary safety item when towing in a hilly or mountainous environment and the Dexter Predator brake controller provides the great control and driver peace of mind knowing that a heavy load can be managed. The unit installs very easily with the proper adapter.
by: Ken D.02/22/2022
Both the 2017 & 2018 Winnebago Forza class A motorhomes DO have in place (under dash) connections for trailer brake controllers, unlike as depicted on your website as needing an additional part (wiring and 4 prong plug), although it is somewhat difficult to find. Attached to the connection socket is an unwired plug (with blue "lips" in somewhat blurry photo). One could either cut and splice the 12" plug-in harness (#20127) into the vehicle connections, or as I did, use solderless socket connections. To determine what wires go where, use an ohmmeter. You will find two b+ wires (use either one) a ground connection, a brake signal wire(use DC voltmeter and press on brake pedal (engine on in diesel pusher) to get reading, and a to trailer wire (bottom left corner when two b+ and ground wire are on right side of socket).
by: kent05/19/2021
If you are starting from scratch to install a brake controller and a 7-Way connector, you would want the Brake Controller 7-and 4-Way Installation Kit (ETBC7). This kit contains all the necessary parts to connect to the 4-Way connector mentioned above, and to wire all the way to the front of the vehicle and connect to the brake controller. I already had a Tekonsha Primus brake controller from another vehicle, so all I needed for that was the Brake Control Plug-in Harness (#20127).
25
735
Show More Reviews Ask the Experts about this Trailer Brake Controller
Do you have a question about this Trailer Brake Controller?
- Can Dexter Predator Brake Controller Fit 2019 Ford Explorer
- Yes the Dexter Predator brake controller part # 58-8 that you referenced does fit your 2019 Ford Explorer by using the install harness part # 3035-S and you'd be set.
view full answer... - Brake Controller Recommendation and Installation on a 2003 GMC Sierra with or without Factory 7-Way
- I did a little research and found that the Dexter Predator, # 58-8, is for 2 to 4 brakes. So if each wheel on your two axle trailer has a brake assembly, or just two of them, this brake controller will work.
Brake controllers are not vehicle or trailer specific, so you will be able to use the best one for your application. I recommend going with a proportional controller because they offer the best and safest braking, and will reduce wear on both the trailer and tow vehicle brakes. I
view full answer... - Will the Dexter Preadator Brake Controller # 58-8 fit a 2006 Cadillac SRX
- Yes, there is a way to install the Dexter Axle Predator Electric Brake Controller # 58-8 in your 2006 Cadillac SRX. The first thing you need is a 4-way trailer connection at the rear of your vehicle. You may already have this, but if not you will need part # C59496. This comes with everything you would need to install the 4-way, I attached install instructions and an install video for you to check out also.
Next, you need to convert the 4-way to a 7-way so that you can install the brake
view full answer... - Installing Dexter Predator DX2 Brake Controller on 2008 GMC Envoy
- As long as your 2008 GMC Envoy is equipped with the factory 7-Way connector there will be blunt cut wires located inside the vehicle on the driver's side under the instrument panel to which your Dexter Predator DX2 Brake Controller # 58-8 can be directly wired. Based on my research there should be a red/black wire that connects to the black (12V power) wire on the controller, a white wire that connects to the white (ground) wire on the controller, a light blue/white wire that gets connected
view full answer... - Troubleshooting Predator DX2 Brake Controller that Only Works with Override Lever
- The controller shouldn't have been showing voltage without a trailer connected. Typically this is caused by corrosion on the 7-way which is putting a slight draw on the circuit and causing the controller to think a trailer is connected.
If the controller isn't applying the brakes with the brake pedal typically that's due to an issue with the red wire of the controller though. This wire needs to see 12 volts to know you are applying the brakes so that it can then start activating the
view full answer... - Location of Brake Controller Connector on 2012 Ram Truck
- The connector you are looking for will be located taped to another larger wiring harness just to the right and above the emergency brake pedal, as shown in the photo I have edited for you.
You can confirm that this is the correct connector by testing it with a circuit tester like part # PTW2993. One pin should show a constant 12-volt power supply, another should show voltage only when the brake pedal is pressed.
Unfortunately, my contact at Tekonsha was not able to shed any light
view full answer... - Trailer Brake Controller Recommendation for a 2014 Chevy Silverado 1500
- If you are concerned there is no where to mount a brake controller (something that comes up a lot since truck interiors are more and more car-like) then I have the perfect solution for you. You can use the Curt Echo Wireless # C51180 that uses a mobile device so it requires no wiring or mounting in your vehicle.
If you determine you want to use a more traditional style controller like the Spectrum # C51170 for a physical button, you will need to cut off the end that plugs into the controller
view full answer... - Is the Dexter Predator DX2 Trailer Brake Controller Compatible with a Triple Axle Trailer
- The Dexter Predator DX2 Trailer Brake Controller # 58-8 is only rated for up to 2 axles. If your trailer has 3 axles then I recommend the Tekonsha Primus IQ # TK90160 which is a proven proportional brake controller at a cost-effective price. This also uses the same wiring configuration as the DX2 so if you are splicing it in to your tow vehicle you will use the following:
Blue - 7-Way Output to Trailer
Black - 12V Power
White - Ground
Red - COLD Side of Stop Light Switch (only gets
view full answer... - Recommended Brake Controller for a 2017 Dodge Durango with Factory Installed Tow Package
- For you 2017 Dodge Durango, i recommend the Tekonsha Prodigy P2 Brake Controller, # 90885. The P2 Brake Controller is a proportional brake controller, so it applies brake power to your trailer in proportion to the brake pressure applied to your vehicle. You will get a faster braking response with proportional controllers over the traditional time delay.
The Prodigy P2 is more of an entry level brake controller; easy to use, easy to mount, and it works well. That is probably why it is
view full answer... - Parts Needed To Install a Dexter Predator DX2 Trailer Brake Controller On a 2022 Chevrolet Tahoe
- The Dexter Predator DX2 Trailer Brake Controller # 58-8 will connect to a 2022 Chevrolet Tahoe with the Tekonsha Custom Wiring Adapter # 3016-S as long as you have the factory tow package with 7-way. You will need to wire the adapter to the controller since Dexter does not put a connector on its controller.
If your Tahoe does not have the factory tow package you will need the Custom Multi-Tow 7-Way and 4-Way Trailer Connectors # 30955 to plug into the wiring on your Tahoe and the controller
view full answer... - Best Trailer Brake Controller for 2004 Chevy Blazer
- For a brake controller for your 2004 Chevy Blazer I recommend the Prodigy P3 Brake Controller part # 90195. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes. This will be the last brake controller you buy as it is incredibly reliable, works, well and is easy to use. It can easily
view full answer... - Where Do the 4 Wires of a Brake Controller Go for Installation in Vehicle
- The four wires and their functions are:
White: Ground wire, connected to negative side of battery.
Blue: Electric brake wire, ran to the brake output circuit of your 7-way with 10 gauge wire like # 10-1-1 sold by the foot.
Black: 12v power wire, connected to the vehicle positive battery terminal with a 40amp circuit breaker, part # 9510.
Red: Stoplight switch circuit. This will get run to the wire on your stoplight pedal assembly that sees voltage only when the brakes are applied.
view full answer... - How to Install a Brake Controller in a 1996 Dodge Ram
- If your 1996 Dodge Ram has the factory 7-way connector at the rear of the vehicle, then all of the wires for the brake controller have been run. You will just need a brake controller wiring adapter. I recommend using part # 3020-P and cutting off the black plug. This adapter plugs into the brake controller plug under the dash, to the left of the steering column taped to another harness near the emergency brake pedal. The four pigtail wires on the other end will be butt-connected to the
view full answer... - Trailer Brake Controller for a 2008 Saab 9-7X with Factory 7-Way Trailer Connector
- The 24 pin receptacle you are seeing sounds like the OBD2 port and would not be used for a brake controller. You will need to utilize the owners manual or a Saab technician to locate the wires and to determine the functions of those wires. Identifying the wire functions is critical because a brake controller has to be hardwired in since there is no plug and play option available.
The wires on a brake controller are as follows:
white is ground
black is 12 volt power in
blue is output
view full answer... - Parts Needed to Install a Trailer Brake Controller on a 1987 Dodge Ram 350 Full Size Van
- The 1987 Dodge full size vans do not have wiring under the dash to wire in a brake controller. You will need to hardwire in the controller using an installation kit. There are different kits depending on whether or not the vehicle has a trailer connector or not.
If your van has a 4-Way trailer wiring harness, you will need to use the 4 and 7 way installation kit # ETBC7. It comes with the 7-Way, wiring, and accessories to wire in the brake controller. If you do not have any type of trailer
view full answer... - Parts Needed To Tow a Towmaster Trailer with Electric Brakes with a Winnebago
- The Dexter Predator brake controller # 58-8 would be a good fit to power the trailer brakes on your Towmaster trailer. You would need to hard wire the brake controller to the Winnebago, connecting the wires coming from the back side of the brake controller as follows.
The brake controller wire functions are:
White: Ground, attached to a clean piece of unpainted metal.
Black: 12v lead, attached to the positive battery terminal on the Winnebago with a 40amp circuit breaker.
Blue:
view full answer... - How to Wire Dexter Predator Brake Controller on a 2013 Town and Country With a Tow Package
- In my research, the 2013 Chrysler Town and Country with a tow package does come with a wiring harness and should have a 7-way. To install the Dexter Predator # 58-8, you will need to run the wires from the brake controller to the 7-way connector on your vehicle.
You are also going to need Draw-Tite # 5506 which gives you the extra length you will need to hook up your brake controller to your 7-way connector.
I have attached a FAQ regarding trailer brake controller installation information,
view full answer... - Brake Controller Does Not Have Full Power When Used
- First, I would go to the 7-way connector and test to make sure you have power. You will want to use a circuit tester, part # PTW2993 to test the wires. Start by testing the Black wire for power, then test the blue wire for brake controller output. To test the blue wire you will need to have a friend help you. With the vehicle in power accessory mode, in park, and parking brake engaged, have them activate the brakes.
Next I would check to make sure the Red Stoplight wire is connected
view full answer... - Can the Predator DX2 Brake Controller Work on a Trailer with 6 Brake Assemblies
- I have a solution for you, but the Dexter Axle Predator Electric Brake Controller # 58-8 that you referenced can only be used on up to 4 brake assemblies.
Instead you would want the Prodigy P2 Brake Controller part # 90885. This controller can be used on up to 8 brake assemblies and would work great for you. This is our best selling controller because of how easy it is to set up and how well it works.
view full answer... - When to Use a 20 or 30 amp Circuit Breaker When Installing Brake Controller
- You'd want to use the 20 amp circuit breaker like # PK54220PL unless your trailer has more than two brake axles. If that's the case you'd want to use the 30 amp breaker # 38630.
view full answer... - Installing a Brake Controller on a 1988 GMC K 1500 Pickup Truck
- GM did not install a brake controller adapter port in the C/K series pick up trucks, so there are no plug-in adapters that will allow you to install a brake controller without having to run wires.
If you already have 7-way connector at the rear of your truck, then you could use wiring kit # 5506. This kit includes a duplex wire to run a brake output circuit from the brake controller to your 7-way and to run a wire from the brake controller to the battery (via the circuit breaker) and
view full answer... - Economical Easy to Install Brake Controller for 2011 Chevy Silverado
- The easiest to install and setup brake controller we offer that's at a great price is the Tekonsha PowerTrac part # 39523 which requires harness part # 20127.
Connect the four wires on the brake controller adapter (20127) to the tow package wires. Follow the table below to connect the tow package wires and adapter wires using butt connectors. I also attached an install video as well.
view full answer... - Replacement Tekonsha Primus IQ Brake Controller Mount and Harness
- For a replacement harness with blunt cut wires you would want the part # 20127.
view full answer... - How to Install a Brake Controller on 2008 Ford Edge with Aftermarket 7-Way
- Since you have a 7-Way you will only need a few more components to complete a brake controller install on your vehicle.
You already have a brake controller so that is one less thing you would need to get.
Next, for a wiring kit to install the brake controller and the 7-way adapter you would want the Wiring Kit for 2 and 4 Brake Electric Brake Controllers # 5506. This will provide the power source and ground for the wiring for the brake controller. You will need to test the wires from
view full answer... - Does Brake Controller Install in 2013 Toyota Tacoma Without Factory 7-Way Require Installation Kit
- I'm not entirely sure what brake controller or wiring you have on your 2013 Toyota Tacoma, but I can tell you that to add a brake controller to your Tacoma you will need to first add Wiring Harness with 4-Pole Flat Trailer Connector # 118496 and then the Universal Installation Kit for Trailer Brake Controller # ETBC7. This is the only way you will be able to add a 7-way and brake controller since you do not have a factory 7-way on your '13 Tacoma.
Once you have installed these you will
view full answer... - Voyager Brake Controller Does Not Show Voltage with Manual Override Applied
- The way a brake controller works is sort of like you described. In many proportion controllers, you actually have to be moving to get voltage when applying the brake but will see voltage when applying the manual override. The controller actually senses how much the vehicle is decelerating using an internal sensor. It does not monitor how hard you press the pedal but it does sense when you are pressing the brake. Of course usually how hard you press the brake does effect the rate of deceleration.
If
view full answer... - Wring Needed for 2000 Dodge Ram to Install Brake Controller
- We can definitely point you in the right direction to get you the needed wiring and a brake controller for your 2000 Dodge Ram. The exact parts you need for the wiring is the following:
- T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118329
- Universal Installation Kit for Trailer Brake Controller # ETBC7
The 4-way is needed for the trailer lights, and will plug into the 7-way that comes with the Installation Kit. These parts will allow you to use a brake controller,
view full answer... - What Pigtail Fits the Reese TowPower 8508211 on My 2007 Dodge Ram Pickup?
- Yes! The pigtail that you need for your Reese TowPower 8508211 is the Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long # 20127. This harness must be spliced into your wiring. We do not have a plug-and-play solution that works.
In order to prep your 2007 Dodge Ram for use with a brake controller, you also need to have a 4-way harness and a 7-way harness installed already. If you don't have these, the parts you need are the T-One 4-way # 119178KIT
view full answer... - Electric Trailer Brake Controller Recommendation for a 2009 Volkswagen Touareg TDI
- I recommend the Tekonsha P2, # 90885. It is one of our highest rated and most popular brake controller models. If your Touareg has a factory tow package, then you will just need to connect the wires from the brake controller to the tow package wires under the dash.
The tow package wiring may be located behind the lower appearance panel beneath the dash and to the right of the emergency brake pedal. It may be on the left, wrapped in grey foam. I have included a link to an FAQ article
view full answer... - What Brake Controller Will Fit My 2022 Chevrolet Suburban
- With your vehicle not having the plug and play option The Tekonsha Prodigy P3 Trailer Brake Controller # 90195 would be the best option. It comes with the plug that splices into the 4 wires that you already have under your dash. The Prodigy P3 can run up to 1-4 axles and has a 360 degree vertical plane operating range.
The Prodigy P3 has 5 storable settings that let you customize the controller for multiple trailers, varying loads, or different drivers.
I have attached an installation
view full answer... - Can the Brake Control Plug-In Harness for Tekonsha and Draw-Tite Be Spliced in at the Tail Light
- In theory you could, but that is not how the Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller # 20127 is designed or intended to be used. It is not what we or the manufacturer would recommend and you would be taking the responsibility into your own hands at that point. Often times the vehicle brake lights get power when the headlights are turned on and you want to be sure that this is wired so that it is only activated when the brakes are applied.
You will want
view full answer... - Replacement Brake Control Plug-In Harness For Tekonsha And Draw-Tite Brake Controllers
- If you're referring to the plug-in harness, we have the Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller # 20127.
This will work with the Tekonsha P3, Voyager, Prodigy, and Primus Brake Controllers. Also works with Draw-Tite Intella-stop Xtreme, Intella-stop Ultra, Intella-stop Digital, and Activator III (5520) brake controllers.
If this isn't what you're looking for, let me know and I'd be glad to assist you.
view full answer... - Tow Package Wiring Colors and Functions for a 2007 GMC Sierra 1500 New Body Style
- the wire bundle you are looking for looks like the one in the FAQ article I have linked for you. It is located under the left side of the instrument panel to the left of the steering column. The wiring colors should be as follows:
Red/black wire = 12 volt power
White = ground
Light blue/white = input from brake switch
Dark blue = output to trailer brakes
Orange = not used
There also may be some connections that you will need to make under the hood to make everything fully functional.
view full answer... - Brake Controller Pigtail Wiring Harness For Infiniti QX 80
- We do carry wiring pigtails for Tekonsha prodigy trailer Brake Controllers that will work on your 2014 Infiniti QX80. I have attached a link to a help article that explains installation of a brake controller.
If you are looking for just the pigtail that attaches to the controller I recommend the Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller, part # 20127. This harness has 12 inch wire leads.
If you prefer a harness with longer wire leads, I recommend the
view full answer... - Troubleshooting Prodigy Trailer Brake Controller Causing Dash Light Errors
- Sounds like it could be the way your brake controller was installed. I would first check the connection of the red wire, this should be connected to the brake light switch wire that is only active (hot) when the brakes are pressed.
Since you have a 2008 this newer body style has been known to need to be hardwired when installing the brake controller to function properly. I have linked a step by step Help Article for you to look at.
I would also recommend to clean out any corrosion
view full answer... - Hardwire Trailer Brake Controller Installation on a 2001 Dodge Van 1500
- Installing a brake controller on your 2001 Dodge 1500 Van is a hardwire installation. In addition to the brake controller and the wiring harness like # 20127, you may also need a 4 and 7 Way Installation kit, # ETBC7 depending on what type of trailer connector is on the van.
If the van already has a 7-Way trailer connector, you will need to add a brake controller installation kit, # 5506. On the back of the 7-Way connector, find the wire that is coming out of the 7:00 position. Cut the
view full answer... - Troubleshooting Brake Controller Only Functioning with Override Lever
- If you have a circuit tester like the part # PTW2993 test the red wire of the brake controller for voltage when the brakes are applied. If there is voltage when you press the brakes then the brake controller is bad but if not then the issue is that you aren't getting a stoplight signal for the controller to allow the controller to know you are applying the brakes. Sometimes this issue is as simple as a blown third brake light fuse or just a bad connection to the vehicle wiring.
view full answer... - Parts Needed to Install an Electric Brake Controller in a 2016 Toyota Highlander with Tow Package
- To install your Prodigy P3 Electric Brake Controller # 90195 into a 2016 Toyota Highlander you can use the wiring harness # 20127. This will plug into the P3 and then hardwire under your dashboard.
If the Highlander needs a 4-way trailer connector the Curt Wiring Harness # 56042 will provide one for you. Then you can use the install kit # ETBC7 to add a 7-way and all of wiring to power your trailer's brakes. If you already have a 4-way then just add the # ETBC7. If you already have
view full answer... - Troubleshooting Hopkins Reliance Brake Controller on 2008 GMC Sierra 1500
- The first suggestion I have is to replace the Hopkins Reliance brake controller, which despite its name is an unreliable brake controller, to say the least. You can still get an economical brake controller that is far more reliable with the Brake EVN # TK63VR with Brake Control Harness # 20127 for your 2008 GMC Sierra 1500.
In regards to the issue you are having, an E1 code on the Reliance means a trailer is not connected and there are a number of potential issues you will need to troubleshoot
view full answer... - Brake Controller Harness For Tekonsha Primus Brake Controller For 2013 Chevy Silverado
- There isn't a plug-and-play wiring harness for any brake controller for a 2013 Chevy Silverado, even with the tow package. So while we do have a harness for your Primus brake controller, it is a splice-in harness:
- Replacement Brake Control Harness # 20127
view full answer...
Info for these parts were:
Expert Research:
Mike L
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Expert Research:
John H
Video Edited:
Zack K
Video Edited:
Joshua S
Video Edited:
Mike H
Video Edited:
Dustin K
Video Edited:
Chris R
Test Fit:
Nicholas E
Test Fit:
Shane H
Test Fit:
David F
Test Fit:
Clayton O
Video by:
Andrew L
Video by:
Zach D
Video by:
Jonathan Y
Video by:
Jacob H
Updated by:
Wilson B
Updated by:
Alexander C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Michael
2/19/2024
After 1 yr and many trips this product has more than exceeded my expectations. Would definitely recommend it to anyone