Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional
Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long
Part Numbers: 39510,20127
Retail:$161.81
Our Price: $116.61
You Save: $45.20
This item qualifies for Free Shipping
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional
part number: 39510
This proportional brake controller is designed to keep towing simple. Includes an LED braking indicator, a slide-bar manual override, and a knob to adjust braking power. Mounts easily within a 90-degree vertical range.
Features:
- Brake controller activates trailer brakes in proportion to your vehicle's braking action
- Automatically adjusts trailer's braking based on deceleration of tow vehicle
- Simple controls keep your settings within easy reach
- Gain setting lets you adjust the amount of power sent to the trailer's brakes
- Slide-bar manual override allows you to control trailer sway or stop in emergencies
- Sensitivity knob lets you set initial braking power and aggressiveness for smooth, safe braking
- Green LED on the top of the module monitors a secure connection with trailer
- Glows red to indicate that trailer brakes are being activated
- Quick and easy installation with included bracket and hardware
- 90-Degree vertical mounting range - must be horizontally level and parallel to direction of travel
- Plug-in, vehicle-specific brake-control adapter available for select vehicles to reduce installation time
Specs:
- Application: trailers with up to 4 axles (8 brake assemblies)
- Compatible with electric brakes only
- Dimensions: 5" long x 3" wide x 1-1/2" tall
- Mounting: between -20 degrees and 70 degrees in the vertical plane
- 5-Year limited warranty
Power and Sensitivity Adjustment
Once the brake controller is installed, you can use the knob on the right side of the unit to adjust the gain (also known as output). Gain lets you set the maximum amount of power that will be applied to your trailer's brakes. You want to set it as high as you can without locking up the brakes. Typically, this setting is only readjusted when you experience changing road conditions or if you switch over from a heavy, loaded trailer to a much lighter, empty trailer, or vice versa.
You can fine-tune the gain by adjusting the sensitivity of the internal sensor using the knob on the left side. This controls the aggressiveness of your trailer's braking, meaning how quickly the brakes reach the maximum braking level. You can adjust this when you're towing heavy loads and you need more umph to bring your trailer to a stop. Your tow vehicle doesn't need that much power to brake in time, but your heavy trailer does. A high sensitivity level will get the braking power to your trailer brakes faster and with more intensity so that it doesn't push your tow vehicle forward.
LED Indicator
Keeping with its simple design, the Voyager will not overwhelm you with information. An LED indicator on the top of the unit lights up green to show that your trailer is securely connected to your tow vehicle. The LED indicator will change to red when the brakes on your trailer are activated.
During installation and setup, this light is also used to ensure that the Voyager will be able to function correctly. Proper leveling of the internal sensor is crucial to the operation of this brake controller. When the sensor is level, the LED will change to a shade of orange.
Simple Installation
The Voyager is designed to be mounted in your cab at a vertical angle that is between -20 degrees and 70 degrees. The brake controller needs to be horizontally level and parallel to the direction of travel in order to function properly.
To connect the Voyager, hardwire the included harness to your vehicle. For a plug-and-play installation, a vehicle-specific wiring adapter is available for select vehicles. One end of the custom adapter plugs into your vehicle, and the other end plugs into the controller - no hardwiring required.
Once the controller is mounted and connected, you must level the internal sensor. First, set the overall power to the maximum using the knob on the side of the controller. Then, while pressing the tow vehicle's brake pedal, adjust the level knob on the other side of the brake controller (this is the same knob that is used to fine-tune the power output) until the LED monitor is a shade of orange.
Installation Accessories
See also etrailer.com's exclusive 7- and 4-way brake-control installation kit (ETBC7 - sold separately) if you don't already have a 7-way plug at the back of your vehicle.
Note: If a custom brake-control wiring adapter is not available for your vehicle, one of the following will be required:
20-Amp circuit breaker (9506P - sold separately) for 2- to 4-brake applications
30-Amp circuit breaker (38630 - sold separately) for 6- to 8-brake applications
Proportional Braking
The Tekonsha Voyager brake controller comes equipped with proportional braking to give you the best towing experience. Proportional braking means that your trailer brakes mimic your tow vehicle's brakes. If you slam on the brakes in your vehicle, your trailer brakes will activate with the same intensity; if you brake lightly, your trailer brakes lightly too. The trailer's braking is in proportion to your vehicle's braking. This saves wear and tear on the tires and the brakes on both your vehicle and trailer.
The Voyager uses a pendulum system to sense how your vehicle is braking so it can send the right amount of braking power to your trailer. It measures the inertia of your tow vehicle and activates the trailer's brakes to slow at the same rate. The result is uniform braking across your towing setup. No push-pull action - just smooth, proportional braking every time.
9030 Tekonsha Voyager Electric Brake Controller - 1 to 4 Axles - Proportional
Item # 39510
California residents: click here
Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long
part number: 20127
Tow Ready Replacement Plugin Harness for the Tekonsha P3, Voyager, Prodigy, and Primus Brake Controllers. Also works with Draw-Tite Intella-stop Xtreme, Intella-stop Ultra, Intella-stop Digital, and Activator III (5520) brake controllers.
- Wire lead length: 12"
- Wire functions:
- Blue: trailer brakes
- White: vehicle battery negative terminal
- Black: vehicle battery positive terminal
- Red: cold side of stoplight switch
8506920 Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long
Replaces 20127
California residents: click here
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- Defective
Customer Reviews
Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional - 39510
Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long - 20127
Average Customer Rating: 4.8 out of 5 stars (1376 Customer Reviews)
This proportional brake controller is designed to keep towing simple. Includes an LED braking indicator, a slide-bar manual override, and a knob to adjust braking power. Mounts easily within a 90-degree vertical range.by: Phil 04/11/2023
I am very satisfied with the Voyager brake Controller I purchased. It is the easiest unit to adjust that I have ever owned. The controls are easy to adjust and it has worked well with my trailers.
by: Corey M.08/01/2020
etrailer makes the purchase easy. I have always used Tekonsha Voyagers, and on my new truck (2015 Silverado) I also wanted the convenience of having the plug and play wiring harness. etrailer had exactly what I needed and was very easy to find on the website. Installation was flawless and clean thanks to the good hardware supplied. Very excited to put some trailers behind the truck with the stopping power confidence that comes with the Voyager.
by: Gary12/26/2020
The Tekonsha Voyager trailer brake controller works well in my 99 Silverado 1500, which was easy to setup for my trailer. The option to allow for different settings of aggression for the trailer braking has allowed the stopping with different loads to be graceful with the turn of a knob. Decided to install the controller in CD storage with velcro for a nice look. Easy access when in place during use for easy observation and twicking during operation. The wife can assist with the twicking while I am driving. Excellent product!
by: Michael 02/18/2023
Exactly what I was looking for and needed ! It was delivered very quick . Actually I just ordered a complete wiring harness from you tonight . Your service and follow up is great
by: Robert G07/15/2016
Completely plug and play installation and works flawlessly, very happy with this unit. I also ordered the exact harness for my 2005 f150 with tow package. Here are a couple of hints that may be helpful. My installation also required a 30 amp cartridge fuse to be installed in the fuse panel in location #105(electric trailer brakes) under the dash on the passenger side. I also installed a relay in location r05 (trailer tow battery charge) but I don't think this is needed for the controller to function. I still had the original trailer brake kit and it had the additional fuse panel instructions and the relay. The owners manual showed where the 30 amp fuse and relay plugs in. You cannot test this unit until a trailer with brakes is connected, ie the led will not light up until it senses a brake circuit.
by: Wayne12/20/2019
The drawtite hitch and trailer wiring harness fit great. Instructions were clear and concise. Installation was a breeze. I am ready to tow my little trailer now. As soon as I get the brake controller installed, I will be ready for my big trailer.
by: Mark01/04/2020
This is my second Tekonsha; I had to replace my 10-year old one after I accidentally broke it.
This one is a bit of an upgrade, and is easily able to lock up the disc brakes on my 15,000 lb trailer. Adjusting it properly, I'm able to brake as though there were no trailer at all. Set it, and forget it. It doesn't get any easier than that.
by: Chris C10/09/2016
If your truck comes with the tow haul package.... this item is literally plug and play. I had it wired up and all mounted inside of thirty minutes. It's literally 4 wires and the stock system wires are labeled along with the brake contoller. I haven't tested it yet but so far I am thoroughly impressed!
by: Alfie07/30/2020
Received this yesterday and was able to install it today. Instructions were very easy to follow and the only problem I had installing it was contorting myself to install the bracket. Once I got the bracket in place the rest was a piece of cake. Went for a test drive as the instructions suggested and did have to tweak it a little but it's doing exactly what I expect it to do. I'll be hauling a John Deere Tractor and wanted to make sure the brakes on the trailer worked.
by: Christopher07/09/2020
Installed in my 2018 Silverado Custom. I ordered the additional wiring harness and the install took less than thirty minutes. Plug and Play at its simplest. Thank You etrailer.
by: Easy install01/21/2021
Perfectly wired directly to existing wiring that I had for the previous brake controller I replaced with the, Draw Tite I Command. This will make it a lot easier should I choose to upgrade the unit in the future.
Fantastic customer service from Joshua as well.
by: Griff Morgan06/19/2022
Class iii Draw Tite trailer hitch:
This part was quick and easy to order and I received it sooner than expected. My mechanic said the installation was easily accomplished and looks great on my car. I would not hesitate to order from etrailer again!
Griff M.
6/21/2023
The product has worked well. I have had no problems with it.
by: Rudy04/20/2023
Purchased this as part of all parts required to convert 1996 Jayco over to electric brakes. Very happy with results. Surprised to see after winter in storage that the battery supply still shows full charge.
by: Bryce05/03/2022
Ram 2500
I installed the Curt gooseneck on my 1993 GMC 2 Wheel Dr. 2500 truck. All the components have tight tolerances. It took me eight hours. With a socket and the wrench. Laying on my back. I did have to cut the wheel well lip about 3/8 of an inch off because I could not get that front angle bar to slide in without hitting it, no way around it unless you lift the bed up and I wasn’t going to do that!!. You have to cut it.instructions do not state that. I’m very happy with the Hitch, it is definitely stout! I did have to make a notch on the outside brackets to go over my airbag bolt. I also had to remove the support bracket on the inside of the frame for the airbag and the crossmember for the spare tire to get the front angled bar in.
by: Michael07/21/2022
Hard to adjust. Had tech at rv place adjust still grabby. Should have got more modern controller
by: Alex 05/01/2024
Plug it in and voila!
by: Jake 08/20/2021
This was an easy install on my 2019 GMC truck using the appropriate wiring adapter. Instructions for setting up the control were clear. After a few adjustments my trailer brakes worked as they should. Minor adjustments of the controller are needed from time to time, but overall the controller is reliable. Good value.
by: Douglas08/03/2023
As always, etrailer delivers. Part was on time and a perfect match for the brake controller. What you don't get from Amazon is the technical support on how to install or use the equipment purchased from etrailer. That's why I keep coming back!
by: Randy04/10/2024
The correct items that fit properly were delivered in a timely manner.
by: Don 03/07/2021
My truck was stolen and wrecked. I was able to retrieve the Tekonsha Brake controller from under the Dash board before it was hauled to the salvage yard, but not the wire harness. I was ale to order a replacement harness from eTrailer and reinstall the controller in my new truck. I had no problems at all. Thank you eTrailer for the great support.
Don
3/9/2022
Still works perfectly after one year. Actually, I been using this Controller for well over a year. I just reinstalled it in my new truck a year ago.
by: Tim 06/21/2020
These guys are great they had the installation kit it came with everything you need and even had a video for my specific vehicle to install the brake controller and wire in a 7 pin trailer plug
If you don’t have factory brake controller the etbc7 is an amazing kit they have comes with everything I mean everything
Tim
6/26/2021
Everything has been excellent e trail has the right products and they fit just like they say
by: Walter Calloway05/24/2015
The product was easy to install with the help of the F-250 adapter. I followed the direction and the product worked just as it was advertised from etrailer.com. If I had to give the Tekonsha Voyager Trailer Break Controller a star rating from 1-5, I would give it a 4.5.
by: Todd D07/24/2015
Easy installation and seems to be a great product. I also used the harness for my 07 new body Silverado for a easy install. Videos are a great help as well . I will purchase all of my trailer and RV needs from ETrailer from now on.
by: Chad07/13/2021
Works as intended, but the plug on the back of the controller is a loose connection. Sometimes I would go to brake and find that I had no trailer brakes because the controller lost power. After a wiggle it would start to work again. I was able to shave the Molex plug a bit and now I don't have any problems with it.
Sierra K.
7/19/2021
Thank you for your review. I have not heard of that problem. I would have used some electrical tape.
by: Bill08/13/2020
The service you receive from etrailer is top notch. This brake controller has worked very well. I actually swap it between two of our vehicles. Just unplug it from one and plug it into the other.
Bill D.
8/15/2021
Very well. The service etrailer provides is the highest Ive ever experienced. They are just super to work with. Ive used them time & time again. I recommend them to everyone looking for anything they carry.
25
1330
Show More Reviews Ask the Experts about this Trailer Brake Controller
Do you have a question about this Trailer Brake Controller?
- Parts Needed To Install Tekonsha Voyager Trailer Brake Controller 39510 In 2018 Chevrolet Suburban
- I would be happy to help.
You will need to use a different plug-in wiring adapter as the adapter your 2002 Chevrolet Suburban uses is different than the one found on your 2018 Suburban.
For your 2018 Suburban you will need the # 3016 given that your vehicle has the factory tow package. This will plug into the factory trailer brake controller port underneath the dash of your vehicle and the directly into your Tekonsha Voyager # 39510.
You will just need to remove the mounting bracket
view full answer... - Trailer Brake Pin on 7-Way Trailer Connector is Hot All of the Time
- There should not be constant 12 volt power at the brake output pin on the back of the 7-way unless the brake pedal in the vehicle is pressed or the manual override is engaged. Since you have a new controller then there is more than likely a short in the brake output wire (usually blue) that runs for the 7-way to the brake controller. You will need to trace this wire back as far as possible while checking for shorts. You can use your multimeter to pinpoint where the short occurs but since
view full answer... - Troubleshooting Tekonsha Voyager 39510 Having Green Light and Sending Constant Power On Blue Wire
- Based on the issue you are having it sounds like the Tekonsha Voyager Trailer Brake Controller # 39510 you have may have an internal short, but there are a few things to try first.
First remove the black wire from the controller to allow it to power off for 15 minutes as this will reset the controller. After the 15 minutes are up go ahead and reattach the black wire with heat shrink butt connector # DW05745-5.
If this did not fix the issue the test the red wire which should be attached
view full answer... - Recommended Brake Controller and Harness for 2009 Chevrolet Silverado
- The trailer brake controller I recommend for a 2009 Chevrolet Silverado is the Tekonsha Voyager Trailer Brake Controller part # 39510. This is a proportional controller which provides the smoothest braking. It's very reliable and overall a great option. In order to install this you will need the Brake Control Plug-In Harness part # 20127. This harness will wire into the four/five wires you already have run under the dash tucked away. It's pretty simple as you can see in the attached video.
There
view full answer... - Can Factory Brake Control Wiring Harness Be Used with Voyager Brake Controller on 2006 GMC Sierra
- You can use the factory wiring harness you have with the Tekonsha Voyager brake controller # 39510. The wire functions on the brake controller are white for ground, black for 12 volt power, red for input from the brake switch, and blue for output to the trailer brakes.
If the functions on the harness for your 2006 GMC Sierra are not labeled then they are likely the following: black for ground, red for 12 volt power, light blue for brake switch input, and dark blue for output to the trailer
view full answer... - Why Would Integrated Brake Controller Not Apply Hard Brakes w Pedal When Trailer is On Jack Stand
- The brake controller in 2013 Chevy Silverado is a proportional brake controller so it would have to sense your vehicle slowing down via inertia for the controller to apply hard braking with the brake pedal. That is why it will function just fine with the override lever but not with the brake pedal.
view full answer... - Is Wiring Harness Needed to Install Prodigy P2 Trailer Brake Controller in 2013 GMC Sierra
- Your Tekonsha Voyager brake controller # 39510 probably installs in your 2013 GMC Sierra with a pigtail wiring harness # TM75127. Older units were hardwired. With this harness already in place in your truck your installation of the excellent Prodigy P2 brake controller # 90885 will be a simple plug-in process. The existing wiring harness will plug in to the back of the P2 with no other parts needed.
view full answer... - Pilot Brake Controller Not Working with 2007 Chevy Silverado New Body Style
- When that light blue wire/red wire attachment was broken it may have caused the stop light fuse to blow. Use the owner's manual to locate the stop light fuse or any fuse related to the brake controller or tow package wiring to see if that is the problem.
If the problem persists, then something likely is damaged inside the controller and it will need to be replaced. But before doing that make sure that light blue wire still has power with the brake pedal by using a circuit tester such
view full answer... - Tekonsha Voyager Operates Only With Brake Switch, Not With Brake Pedal
- I can explain the blue wire. On the 2005 Dodge Ram, vehicles that had the factory 4-pole trailer connector didn't have the blue wire from the under dash connector ran all the way to the back. The blue wire terminated in the engine compartment. Since it's easier to access the wire behind the brake controller, many folks just tap into it there.
The first thing you'll want to do is to use a circuit tester like part # PTW2993 and test the red wire exiting the rear of the brake controller.
view full answer... - Replacement Install Harness for Tekonsha Brake Controller
- The universal replacement brake controller harness for Tekonsha brake controller is the part # 20127 which has blunt cut wires like you may have currently. I'm fairly certain you have a 1998 Dodge Ram though so if you wanted the harness that plugged into the back of your controller and then to the port under the dash of your truck the part # 3020-P.
If you are missing the female connector on the brake controller we don't have a replacement for that but you could use the # 3020-S to wire
view full answer... - What are the Different Knobs on a Tekonsha Voyager
- The Tekonsha Voyager # 39510 has both a Power Knob (right side) and a Level Knob (left side). Whereas the right side is for fine tuning the brakes, the left knob will be for the more basic power level coming out of the controller to the brakes on the trailer. I included an install of this controller for you to take a look as as well.
view full answer... - Troubleshooting LED Indicator Light on Tekonsha Voyager Brake Controller 39510
- The green light on the Voyager brake controller # 39510 should come on as soon as you plug the trailer into the vehicle. If it does not come on at all, this indicates that you either have some corrosion inside the trailer or vehicle plugs that is causing a short, or you have a loose power or ground connection. Check the plugs on both sides of the setup for any white or green corrosion. If you see any, clean the plug thoroughly or just replace it.
If you don't see any buildup in
view full answer... - Hardwiring in Brake Controller to 2007 Dodge Ram 1500 with Factory 4-Way and Active Port Under Dash
- A couple of things:
We recommend a 40 amp circuit breaker on the 12 volt circuit to the 7-Way. This is because you never know what you might tow! For a 40 amp circuit breaker you can use # PK54540.
The wire match ups you provided are correct. The only issue is if the harness under the dash is actually fully active. It is possible that it is but it also might not be. The only way to know other than testing with a circuit tester is to try it. though it sounds like you tested and it
view full answer... - Brake Controller Installation on a 2004 Chevy Suburban
- Trailer brake controllers are not vehicle specific so you can use any of them on your 2004 Chevy Suburban. If your Suburban came with a factory 7-Way all you would need to install the Voyager brake controller # 39510 is wiring harness # 3015-P. I have linked a video that shows where you will plug in the controller on your Suburban.
If your Suburban did not come with a 7-Way trailer connector then you would also need to add one using # 30955.
There may also be some connections you
view full answer... - LED Light on Tekonsha Voyager Trailer Brake Controller # 39510 No Longer Lights Up
- Normally LED lights (light emitting diodes, actually) have a very long lifespan, far longer than standard incandescent lights. Usually an LED in a device will last longer than the device itself. Despite this it is still possible that the LED on your Voyager brake controller has simply burned out. If the trailer brakes are operating properly and in all other respects the controller is working normally, then this is likely to be the case.
If your Voyager is still within its 5-year warranty
view full answer... - Do Tekonsha Voyager and Prodigy Brake Controller Use the Same Wiring Adapter for Installation
- Yes, you can easily replace the Tekonsha Voyager brake controller # 39510 in your 2007 Toyota Tacoma with the outstanding Prodigy P3 # 90195 simply by unplugging the old controller and plugging in the P3 using the same wiring adapter # 3040-P.
view full answer... - Troubleshooting Tekonsha Voyager Brake Controller part # 39510 with No Brake Output
- The manual override lever of the Tekonsha Voyager Brake Controller part # 39510 that you have should still put voltage on the blue output wire. If the controller is wired and installed correctly to your vehicle and it's still not working then the controller is most likely in need of replacing.
For a replacement I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup.
view full answer... - Trailer Brakes Do Not Activate with Brake Pedal Using Voyager Controller on a 2012 Nissan Xterra
- Usually when a brake controller does not work with the brake pedal that indicates a problem on the red wire. The connection at the red wire will need to be examined and possibly reconnected. You may also have a blown stop light or CHMSL fuse that you can change. Use the vehicle owners manual to find the fuse locations.
If everything checks out with the vehicle including power to the brake controller along the red wire when you step on the brake pedal then there is a problem inside the
view full answer... - Installing Tekonsha Voyager Trailer Brake Controller # 39510 in a 2010 Ford F-150
- Trailer brake controllers like your Tekonsha Voyager # 39510 are not vehicle-specific and so can be installed in any vehicle. The four wires for a controller - black, blue, white and red - are standardized for specific functions: BLACK is 12V power input to the controller (via a circuit breaker); BLUE is the controller's output signal which gets routed to the 7-way; WHITE is a ground that connects either to the vehicle frame or to the battery negative terminal; RED is the input trigger
view full answer... - Factory Port Location for a Brake Controller Wiring Harness on a 1999 Dodge Ram
- I show that the Tekonsha Plug-In Brake Control Wiring Adapter, Dodge, item # 3020-P, and it works on all Dodge Ram Pickups from 1995 - 2009. You should be able to use the adapter that is connected to your Tekonsha Voyager brake controller, item # 39510, on your 1999 Dodge Ram. I believe you are looking at the wrong connector under the dash.
You will need to look under the dash, near the emergency brake pedal for a white or blue connector that is above a white junction box. This is where
view full answer... - Tow Package Wiring Colors and Functions for a 2007 GMC Sierra 1500 New Body Style
- the wire bundle you are looking for looks like the one in the FAQ article I have linked for you. It is located under the left side of the instrument panel to the left of the steering column. The wiring colors should be as follows:
Red/black wire = 12 volt power
White = ground
Light blue/white = input from brake switch
Dark blue = output to trailer brakes
Orange = not used
There also may be some connections that you will need to make under the hood to make everything fully functional.
view full answer... - Troubleshooting No Power to Brake Controller 12 Volt Power Wire On a 2013 Chevrolet Avalanche
- There is one additional step that is required on your 2013 Chevrolet Avalanche that was not covered in the video with the 2012 Chevrolet Silverado. There is a red wire located just outside the engine compartment fuse box that needs to be attached to one of the front lugs inside the fuse box. You will need the M8 Nut # 185917 to complete this step. I have linked a video below for an installation we did on a similar Avalanche so you can see the additional step towards the end of the video.
view full answer... - Troubleshooting Brake Controller Only Functioning with Override Lever
- If you have a circuit tester like the part # PTW2993 test the red wire of the brake controller for voltage when the brakes are applied. If there is voltage when you press the brakes then the brake controller is bad but if not then the issue is that you aren't getting a stoplight signal for the controller to allow the controller to know you are applying the brakes. Sometimes this issue is as simple as a blown third brake light fuse or just a bad connection to the vehicle wiring.
view full answer... - Parts Needed to Install a Primus Brake Controller on a 2007 Toyota Tacoma and 2008 GMC Yukon
- For the 2007 Toyota Tacoma, if it is using wiring harness # 3040-P then you will not need anything else for the Tacoma. Or if using the factory Toyota harness you could replace it with # 3040-P. The harness will plug into the Primus brake controller # TK90160. I have linked a video showing how it would install on your generation Tacoma.
On the 2008 GMC Yukon you will need plug-in harness # 20127 because the Yukon has a tow package wire bundle under the dash and not a place to plug into.
view full answer... - Wring Needed for 2000 Dodge Ram to Install Brake Controller
- We can definitely point you in the right direction to get you the needed wiring and a brake controller for your 2000 Dodge Ram. The exact parts you need for the wiring is the following:
- T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118329
- Universal Installation Kit for Trailer Brake Controller # ETBC7
The 4-way is needed for the trailer lights, and will plug into the 7-way that comes with the Installation Kit. These parts will allow you to use a brake controller,
view full answer... - What Pigtail Fits the Reese TowPower 8508211 on My 2007 Dodge Ram Pickup?
- Yes! The pigtail that you need for your Reese TowPower 8508211 is the Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long # 20127. This harness must be spliced into your wiring. We do not have a plug-and-play solution that works.
In order to prep your 2007 Dodge Ram for use with a brake controller, you also need to have a 4-way harness and a 7-way harness installed already. If you don't have these, the parts you need are the T-One 4-way # 119178KIT
view full answer... - Brake Controller Install Harness Recommendation for a 2014 Toyota Tacoma
- To install your Prodigy P2 # 90885 in your 2014 Toyota Tacoma you would need the install harness part # 3040-P as it has been custom fit for your truck. This harness is 32 inches in length.
I attached an install video that shows this harness being installed in a similar Tacoma as yours.
view full answer... - Brake Controller Recommendation for 2013 Ford Edge
- There is one other part you will need so you can install a brake controller to your 2013 Ford Edge, the Universal Installation Kit for Trailer Brake Controller # ETBC7.
This will give you the 7-way connector, circuit breakers and rest of the hardware needed to install a brake controller, and work with your '13 Edge's hitch like the Draw-Tite # 75992 and 4-Way Wiring Harness # 118515.
Once you have all of this installed the brake controller I recommend for your 2013 Ford Edge is the
view full answer... - Location of Brake Controller Wires on a 2009 Chevrolet Avalanche
- The wiring harness used to install a brake controller on your 2009 Chevrolet Avalanche would have been present regardless of whether or not your truck came with a factory trailer connector. If you take a look at the :20 mark in the attached video, the location of the wires will be revealed. Please note that these are blunt cut wires taped to an existing plug. In order to install your Reese brake controller you will also need the pigtail part # 20127 if you do not already have one.
If
view full answer... - Trailer Wiring to Add 7-Way to 2014 Jeep Grand Cherokee
- We can help you out here, as there's a couple of parts you will need for your 2014 Jeep Grand Cherokee in order to use your trailer's electric brakes, with the he correct parts being the following:
- Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat # C62VR
- Universal Installation Kit for Trailer Brake Controller # ETBC7
The 4-way is needed in order to activate the lighting functions on your trailer, and it will plug right into the 7-way adapter that comes with the # ETBC7.
view full answer... - Replacement Hardwire Brake Controller Adapter For Prodigy P3
- You'll need to hardwire the Prodigy P3, which means the correct adapter is the Replacement Brake Control Harness # 20127.
If you do not have a factory brake controller on your Ram you will not need to have it flashed; if you are replacing the factory brake controller there is a good chance you will (this is not a one size fits all answer which is why I can't give you a definitive yes).
view full answer... - Where to Connect the Stoplight Wire on Brake Controller Pigtail
- To install the Tekonsha PowerTrac Brake Controller # 39523 in your 2006 Ford Escape, the red wire on your brake controller harness # 20127 needs to be connected to the stoplight switch under the dash in your vehicle.
There should be a wire for the stoplight switch on the back of the brake pedal. You will want to use a circuit tester, like # PTW2993, to find the wire that has signal only when the brake pedal is depressed. Testing the wires is the best way to be sure which wire is the
view full answer... - Where to Splice Brake Light Wire From Brake Controller To Stoplight Wire
- Since your vehicle does not have a brake controller port, you will want to use a universal wiring pigtail. For example, if you have a Tekonsha brake controller, you could use a Plug-In Harness for Tekonsha and Draw-Tite Brake Controllers # 20127. You will want to use a circuit tester, like # PTW2993, to test the wires at the stoplight switch at the back of your brake pedal to find the wire that only has signal when the brake pedal is depressed.
Once you have found the wire that only
view full answer... - Trailer Brakes Only Working With Manual Override on 2011 GMC Sierra
- If your trailer brakes are only working when you apply the manual override the issue is commonly the red wire - the stop light switch. Make sure it is connected to the circuit that that only sees voltage when the brakes are applied. The issue with not displaying numbers does make me think that the brake controller may have hit the fritz and need to be replaced though, and this would be true if the numbers never display, even when using the manual override.
For your 2011 GMC Sierra a
view full answer... - Harness Needed To Install Tekonsha Brake Controller on a 2002 Toyota Tundra
- In order to install a Tekonsha brake controller on a 2002 Toyota Tundra you'll need the Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controllers part # 20127. This harness plugs directly into the brake controller and then the other end splices into the circuits on the vehicle. Please note, there is no brake controller port on a 2002 Toyota Tundra so splicing is the only option.
view full answer... - Brake Controller Wiring Functions to Install on a 1990 Dodge D250 Pickup
- The red wire that disappears under the dash of your 1990 dodge D250 pickup is input from the brake switch and will go to the red wire on the brake controller. Blue is output to the trailer brakes and connects to the blue wire on the brake controller.
White is ground as you know and connects to the controller white wire and the fused red wire is for power which connects to the black brake controller wire. If you had switched the other red wire and the blue wire nothing would have happened
view full answer... - Stop Light Switch Location On A 2015 Jeep Cherokee
- The stop light switch that you will need to connect the red wire to on the Brake Control Plug-In Harness for Tekonsha part # 20127 may be pre ran to a set of wires taped to the underside of the drivers side vehicle dash. If the wires are not present in this location, I recommend installing a stop light switch such as the Roadmaster Stop Light Switch Kit part # RM-751471 to wire the brake controller stop light switch to because of the difficulty and risk of error that is involved when splicing
view full answer... - Which Brake Switch Wire is Used When Installing Brake Controller on 2008 Dodge Ram 1500
- A brake controller has four wires exiting the rear of the controller, they attach as follows: the red wire attaches to the brake stoplight switch located at the top of the brake pedal. The color of the correct wire on the brake switch is usually a white wire with a tan stripe, but it could vary so it is best to find the correct wire you will need by testing the wires for function. The stoplight switch can have several wires exiting it, you will need a circuit tester like Quickee Tester,
view full answer... - Voyager Brake Controller Does Not Show Voltage with Manual Override Applied
- The way a brake controller works is sort of like you described. In many proportion controllers, you actually have to be moving to get voltage when applying the brake but will see voltage when applying the manual override. The controller actually senses how much the vehicle is decelerating using an internal sensor. It does not monitor how hard you press the pedal but it does sense when you are pressing the brake. Of course usually how hard you press the brake does effect the rate of deceleration.
If
view full answer... - Installing a Brake Controller on 2013 Mazda CX-5 with 7-Way Installed
- Since you have a 7-Way you will only need a few more components to complete a brake controller install on your vehicle.
For a wiring kit to install the brake controller and the 7-way adapter you would want the Wiring Kit for 2 and 4 Brake Electric Brake Controllers # 5506. This will provide the power source and ground for the wiring for the brake controller. You will need to test the wires from the brake pedal switch of your vehicle to find a circuit that has voltage when the brakes
view full answer...
Info for these parts were:
Expert Research:
Mike L
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Expert Research:
John H
Video Edited:
Zack K
Video Edited:
Joshua S
Video Edited:
Mike H
Video Edited:
Dustin K
Video Edited:
Chris R
Test Fit:
Nicholas E
Test Fit:
Shane H
Test Fit:
David F
Test Fit:
Clayton O
Video by:
Andrew L
Video by:
Zach D
Video by:
Jonathan Y
Video by:
Jacob H
Updated by:
Wilson B
Updated by:
Alexander C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Michael
2/19/2024
After 1 yr and many trips this product has more than exceeded my expectations. Would definitely recommend it to anyone