Summer Starts Here - Save up to 70%
Part Numbers: 39523,20127
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This time-delayed brake controller is designed to mount at any angle, even upside down. The controls are all up front for easy access, including a slide-bar manual override and a thumbwheel for braking output. LED indicator shows your braking status.
Features:
Specs:
The Tekonsha POD is designed to mount in any direction, and it's especially suited for mounting on near-vertical dashes. All the controls are on the front of the module, so you can still access them with the controller tucked away in a convenient place.
Braking output is the maximum amount of power that will be applied to your trailer's brakes. How much braking output you need is determined by the weight of your trailer; a heavier trailer will need more power to bring it to a stop. You want to set the braking output as high as you can without locking up the brakes. Once you've set up the brake controller the first time, you shouldn't need to adjust the settings until the trailer load changes, you switch trailers, or road conditions change. Use the thumbwheel on the side to change the braking output level. The output setting will appear as a number on the digital display, with a higher number indicating higher braking power.
The Tekonsha POD keeps the manual override within easy reach on the front of the module, great for stopping sway or controlling your trailer's momentum in emergencies. Push the slide-bar lever to activate the trailer's brakes and brake lights without you having to apply the brakes on your tow vehicle, perfect for limiting trailer movement while you re cruising.
Because inertia plays no role in the functioning of this controller, you do not have to mount the unit at any particular angle. Your mounting options are limitless, with the controller designed with all of the controls on the front of the module so you can access them even if it's mounted upside down.
If your vehicle already has a plug-in brake controller wiring harness, just connect the unit to it. Otherwise, you will need to purchase a vehicle-specific wiring harness (sold separately) to plug into. If a harness is unavailable for your vehicle, hardwiring will be necessary.
See also etrailer.com's exclusive 7- and 4-way brake control installation kit (ETBC7 - sold separately) if you don't already have a 7-way plug at the back of your vehicle.
Note: If a custom brake control wiring adapter is not available for your vehicle, a 20-amp circuit breaker (sold separately) may be required for installation.
The Tekonsha POD comes equipped with time-delayed braking. Every time you apply the brakes in your vehicle, a signal is sent - via the brake switch - to the POD. The controller then sends power out to your trailer brakes to activate them with an intensity set by you, at a rate determined by you. The amount of braking power (output) can be adjusted to suit your preference, the road conditions, the type of trailer, and the weight of your load. To determine which levels are best for your application, test your towing setup and choose what feels right.
California residents: click here
Tow Ready Replacement Plugin Harness for the Tekonsha P3, Voyager, Prodigy, and Primus Brake Controllers. Also works with Draw-Tite Intella-stop Xtreme, Intella-stop Ultra, Intella-stop Digital, and Activator III (5520) brake controllers.
California residents: click here
Average Customer Rating: 4.8 out of 5 stars (1930 Customer Reviews)
This time-delayed brake controller is designed to mount at any angle, even upside down. The controls are all up front for easy access, including a slide-bar manual override and a thumbwheel for braking output. LED indicator shows your braking status.Great little brake controller for the money if you don't need heavy braking on a larger trailer. Simple and economic.
We have a Honda Ridgeline and needed this for our camper trailer. It was nice ordering the specific plug in wire for the Ridgeline and therefore eliminating hard wiring, just plugged it in. It was rough getting to the factory plug under the dash by the emergency brake petal switch. My hands are not small enough, ha ha. But success was had. Plugged into the controller and mounted it and u-wall-a. It works the way it is suppose to, I like that. A good quality unit that does what it is suppose to. thanks.
Very happy with this product. It fit nicely in my truck and plugged right into the factory wiring harness. Total installation time was under an hour. Easy to adjust, and works perfectly with my 5th wheel trailer. I simply pulled out the little storage cubby from the dash, cut the back off, slid the controller in, bolted it together, and stuck it all back in the dash. Looks and works great.
Exactly what I was looking for and needed ! It was delivered very quick . Actually I just ordered a complete wiring harness from you tonight . Your service and follow up is great
Worked out perfectly for me, super easy installation with adapter harness. Work's flawlessly, easy one hand gain control with control's on front. My truck had nice cubby it fit in so out of the way and seamless look. Thanks for a great product and service.
Purchased a Teckonsha Voyager brake controller and the ETBC7 install kit.
The instruction an video were very clear and easy to follow. Installed on a 2007 Ford Ranger Sport. Tech support was also very helpful on the one question I did have.
David
11/8/2020
I have been completely satisfied with this item. It has operated as advertised an has had no problems.
I sell and install a variety of components for various companies and individuals. I have zero comebacks from this company. Not that I haven't received defective parts but they always make it right. And that is good business.
I have a Toyota Tacoma (06). I had the controller installed in less than five minutes. One minute to gather the tools: drill/bits, screw driver, and tape. I thought tape would be helpful to hold the ground screw to the driver given the tight are under the dash. One minute to drill the ground hole. One minute to install the ground screw. One minute to plug in the cables and fish the wire under the stirring wheel to allow for the controller to be mounted in the storage area found on Tacoma trucks dash. I guess I was wrong. It only took four minutes. I did not need to put the tools away I was off to do other projects. I rate the product as good because I have not tried it on the trailer yet.
Easy to install in my Toyota-Tacoma 2012. I pull my Travel Trailer and this break controller worked very well and with just a little bit adjustment. Also this item was shipped very fast.
I received my purchase very quickly.
I just installed the control and wire harness today. Installation was easy, all you need are basic hand tools and a drill with a small bit.
Haven't had chance to test it out yet but, when I do I'll update.
The brake controller we purchased and had professionally installed works perfectly. We had it installed in our RV for use when towing a large vehicle trailer. It's reliable and simple. It was a great purchase!
Have used the power track for a year with city and interstate travel and a 4000# single axle TT. Working flawlessly on my 20 Blazer using a bypass stoplight switch.
Thanks to etrailer’s video “Trailer Brake Controller Installation - 2004 Jeep Grand Cherokee”, the installation of a Tekonsha PowerTrac controller on my 2003 Jeep was very straight forward (and I’m not a car guy!). Like in the video, I used the wiring kit (#5506). I forgot to order a pigtail wiring harness but was able to pick one up locally. Took the trailer out last weekend and the brakes worked great.
The drawtite hitch and trailer wiring harness fit great. Instructions were clear and concise. Installation was a breeze. I am ready to tow my little trailer now. As soon as I get the brake controller installed, I will be ready for my big trailer.
The controller was a great option for our 2021 forest river FSX and gave me plenty of control over the brakes. It does require a adjustment time to time but has always worked when brakes are applied. The setup and installation were a breeze and has worked for many trips.
I ordered everything to install hitch an and 7 pin plug. Everything went great. Parts were all perfect and instructions easy to follow.
The control works great. Nice incremental application of wheel from nothing to hard on! Led light goes from green to red also in incremental degrees. Installation was a snap in my 2008 F150 with tow package. Just Plug in the control clip and the other end in the terminal above and to the right of the computer check terminal. Rather than have it below my dash I opted for the cove below the lighter. Etrailer did a nice job of getting out to me right away and kept me informed where this was at all the way to my door. Good Job!
If your truck comes with the tow haul package.... this item is literally plug and play. I had it wired up and all mounted inside of thirty minutes. It's literally 4 wires and the stock system wires are labeled along with the brake contoller. I haven't tested it yet but so far I am thoroughly impressed!
Product arrived quickly and installed very easily. Plug and play with the correct adapter (3035-P Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford, Lincoln, Mercury) for a 2001 Ford F-150. Controller is very easy to set the braking on your trailer.
I ordered the powertrac with the 22292, 2011 ford F150 wiring adapter, It works great. 15 mins, and I had everything ready to go. It is a little sensitive to adjust but ones you get the feel for it, it takes no time to adjust. very happy with this unit, I would recommend this unit to everyone.
Installed on 2003 Toyota Tundra with the factory tow package. Installation was a breeze with the included vehicle specific wiring adapter. It took me about 45 minutes total. Looks professionally installed. Easy to use. Set the adjustment for your specific trailer and go!
Perfectly wired directly to existing wiring that I had for the previous brake controller I replaced with the, Draw Tite I Command. This will make it a lot easier should I choose to upgrade the unit in the future.
Fantastic customer service from Joshua as well.
Same as the adapter plug , just mount , plug and play.
Class iii Draw Tite trailer hitch:
This part was quick and easy to order and I received it sooner than expected. My mechanic said the installation was easily accomplished and looks great on my car. I would not hesitate to order from etrailer again!
Griff M.
6/21/2023
The product has worked well. I have had no problems with it.
Purchased this as part of all parts required to convert 1996 Jayco over to electric brakes. Very happy with results. Surprised to see after winter in storage that the battery supply still shows full charge.
Ask the Experts about this Trailer Brake Controller
Do you have a question about this Trailer Brake Controller?
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Michael
2/19/2024
After 1 yr and many trips this product has more than exceeded my expectations. Would definitely recommend it to anyone