Camper Jacks Specs:
Features:
Improve the stability of your parked and leveled RV with these base pads. 7" Tall pads fit under smaller units as well as units with a higher clearance. Stack 2 pads to get 12-3/8" of height and a 3,500-lb load capacity.
More Information >RV Jack Pads Specs:
Features:
Replaces 6 pads for your SnapPad jack stand pad system. Pads increase the surface area of the jack feet to help prevent sinking and provide added stability. 4 Pads fit 9" round jack feet. 2 Pads fit 11-1/2" or 12" round jack feet.
More Information >Videos
for RV Jack Pads
Help Articles
for RV Jack Pads
Expert Answers
for RV Jack Pads
I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.
view full answer...We do offer a few kayak carriers that you can use with the Thule TracRac TracONE Truck Bed Ladder Rack. You will need to use a channel mount carrier. Since the crossbars on the TracOne are a bit oversized, none of the clamp on carriers we sell will…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where…
view full answer...I am sorry but we do not have an AC cover with those dimensions. The closest option we have is the Replacement RV Air Conditioner Cover for Penguin and Dometic Air Conditioners item #AT3308046006 which measures…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5"…
view full answer...I went out to our warehouse and test fit some SnapPads on the feet of the Lippert High-Speed Power Stabilizer Jack #LC298707 and found that the 6" square SnapPads were a fit. If your 2022 Forest…
view full answer...Kenny, those bolts for the B&W Companion 5th Wheel Trailer Hitch #BWRVK3500-5W should be torqued to 40 ft. lbs. Also, the pivot arms would need to be torqued to 80 ft. lbs, the draw down bolt should…
view full answer...The proper replacement inner assembly member for your UFP 34043 would be indeed be the the Dexter #DX99FR which is compatible with disc brakes. The replacement has an electric lock out and has a 7500K capacity and is intended to work with a 2 inch…
view full answer...SnapPads like the SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 9" Round Jack Feet - Qty 6 Item #SP54FR6 can be taken off and on as needed so you…
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...The Stromberg Carlson RV Jack Pads for RVs and Trailers - 14" Long x 12" Wide - Rubber - Qty 2, part #SC37VR will fit the jack feet of your 2022 Tiffin…
view full answer...