Hey David, the Derale transmission cooler part #D15200 that you referenced does not come with a thermostat or any install kit components but if you wanted a similar option that does have all of that you would want the part #D15500.
That's pretty hard to give an exact answer on but with the install of the Derale Electra-Cool Combo Engine and Transmission Cooler Assembly w/ Fan #D15200 you'd see the fluid stay right around 175 degrees in traffic on a hot day since the fan…
Many of the Grand Design Imagine RV's are pre-wired for the Furrion Vision S Wireless RV Backup Camera System. This is available in two different configurations; #FOS43TASF for 4.3" or the #FOS05TASF for a 5"monitor. These are both…
In regards to the Derale Thermal Fan Clutch with Reverse Rotation part #D22140, the distance from the mounting surface to the end of the shaft is 1-13/16" and the distance from the mounting surface to the end of the clutch is 1-3/4". I went…
The correct hub and drum assembly to use with the Dexter Trailer Axle Beam with E-Z Lube Spindles #6340624 is the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ. A set of this hub and drum have a 5,200 lb capacity just like the axle, has an E-Z…
The Dexter Trailer Hub and Drum Assembly, part #84546UC3, is a trailer hub and drum with the lug nuts, bearings, bearing races, grease cap and grease seal included. It is designed to fit 3,500-lb axles. After removing your old drum and cleaning the…
Hey Brian, yes the grease seal of the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles #AKHD-545-35-EZ-K is designed to prevent grease from getting on the brake components. But what I would guess happened to you is that you overfilled the hub…
We will have several different pre packed hub assemblies for you to choose from depending on if you need a hub for drum brakes or hubs for an idler axle. Here is a list of hubs for both drum and idler axles in the different bolt patterns that use the…
Hey Jairo. So we do not offer a direct replacement for the Norcold N611, but we do have a good replacement option for you. It really comes down to what will fit in your cutout space. Take a look at the Norcold RV Refrigerator w/ Freezer - 8.2 cu ft -…
We have an abundance of steps for you to choose from whether you prefer to replace the current steps on your Jayco Eagle or use free-standing steps such as the Econo Porch Trailer Step, #EHS-102-R-HR. However, RV steps are not specific to the make,…
All the brake controller needs to sense a trailer connection so that you can test it is a slight amperage draw on the output circuit. For that you can use a circuit tester like the part #PTW2993 with one pin grounded and the other on the output pin.…
I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future.
Kevin
Manchester, MD
Radiator Fans with 13 Inch Diameter for confident cooling
Go with 13 inch diameter fans when you want solid airflow in a compact package. To choose the right one, look at the fan from the front of the motor: clockwise is standard rotation, counter-clockwise is reverse rotation. Match the size and rotation to your current setup for reliable cooling performance.
Yes, you can choose a replacement by going by the size of the old fan and matching rotation. Stand in front of the motor to confirm clockwise (standard) or counter-clockwise (reverse). Verify the center locating hole fits your hub. Double-check clearance around the shroud and radiator before tightening everything down.
Measure the space in your shroud or between the radiator and engine to confirm a 13 inch diameter clears. Check overall depth so the fan doesn't contact the radiator or accessories. Verify the center locating hole matches your water pump hub. Make sure the rotation matches your pulley setup.
Stand in front of the car facing the motor and watch the fan direction. If it turns clockwise it is standard rotation; if it turns counter-clockwise it is reverse rotation. Match the fan's rotation and 13 inch size to your setup before ordering. Confirm the fan blades are oriented for the rotation you need.
It can improve cooling when the size and rotation match your setup. Verify there's room for a 13 inch diameter fan and that it clears the radiator, belts, and hoses. Check that the center locating hole fits your water pump hub. Test idle and low-speed temps after install to confirm results.
Filters
