The Replacement Standard Dual Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side, #LC84FR is the left side of the slide-out as looking at it, facing it, from the outside. The float side, #LC26VR, will of course be the right side as facing…
Hey Stephen, we have the 16 foot etrailer awning part #e84QV that would work great on your car hauler. How tall is the side of the trailer? It shouldn't be a problem but the arms of this awning are 69 inches tall. We spent a lot of time on our…
Hey Jack congrats on the new Jeep! To flat tow a 2021 Jeep Wrangler Rubicon behind your 2012 Thor Hurricane 31J motorhome, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect…
Hello Andrew, good question. Basically the only difference between the composite kits and the standard (non-composite) kits is the application they are used for. Composite are used in motorhomes, the other are used on towable campers. It has to do…
Hey Jared, the pass through amp rating of the Rich Solar NOVA 3K12 3000W 12V Pure Sine Wave Inverter with Built-in Transfer Switch for RVs #RS79VR is 30 amps. What AC units do you have? This should be more than enough for that.
Hey, Skip! Happy to help get your new Jeep set up for flat towing. There is going to be a list of parts, so I'll go ahead and list them all below for ya. Blue Ox Base Plate: Part #BX1139 Blue Ox Avail Non-Binding Tow Bar: Part #BX7420 Demco…
Unfortunately, I cannot tell you what wiper seal you would need for your 2004 Keystone Outback. This is not something that is known just from the RV information. It depends on your particular slide-out. The best way to determine what wiper seal you…
Hey Donna, you would have to replace the entire setup as there was a refrigerant law change in January of 2025 that forced the complete systems to have to be redesigned and because of that nothing is currently backwards compatible. So what I would…
Hey John! Since you have the same number of teeth the Replacement 24 Tooth Pinion Spur Gear for Power Gear RV Slide Outs #LC86EX will likely work as a replacement. I would measure the outer diameter as well. If it matches the 1.417" measurement…
The Fixed Dual Rack Repair Kit #LC84FR goes on the left side of the slide as you look at the slide out from the outside of the camper. So on the drivers side it will be the front of the slide. The Floating Dual Rack Repair Kit #LC26VR is going to be…
You've got both a wiper seal and a bulb seal here with the wiper seals having a track for the bulb seal to slide onto. The Rubber Wiper Seal with Track for RV Slide Out #SR87FR you were already looking at is most likely the closest option to what…
Hey Kyle, yes the Flair-It High Pressure Hose #FL37FR does fit on the 1/2 barb fitting of the Flair-It PEXLock Female Elbow Fitting #FL44ZR that you also referenced.
Swapping out worn weather stripping is easy with Clean Seal seals built for RV slide outs. Match the side profile and dimensions—bulb and flange fit—then choose a length such as 15', 25', or 50' to cover your run. These bulb styles fit over a flange and can replace original styles on aging motorhomes.
Yes, they press onto the flange and go on easy when the flange size and profile match. Check your flange width against the seal's receptor, such as a 1/2" flange portion if noted. Compare the side profile to your original to confirm bulb size and placement. If the old seal lost grip, verify the new seal clamps firmly along the run.
It can work if the dimensions and side profile match, but it's intended for RV slide outs. If you don't have OEM specs to compare, match the cross-section visually and by measurement. For reference, one option is 15' long x 1-5/16" wide x 1" tall. Confirm the flange fit and bulb placement before committing.
Measure your flange and bulb, then match the side profile and dimensions. Clean Seal press-on options include a 7/8 inch wide bulb and seals with a 1/2" flange portion. Lengths include 15', 25', and 50'. If your original used a specific bulb placement, compare for straight-in-line vs slightly offset to help ensure a proper seal.
There are Clean Seal options with a 1/2" flange portion and a bulb near 3/4", and others with a bulb closer to 1/2". Measure both parts on your original. Also check if your old bulb was straight in line or slightly offset—mismatch in placement can affect contact and sealing. Choose the closest side-profile match for best results.
Filters
