Most Popular 3/4 Inch Ball Hole Diameter for Chrysler Town and Country

The hitch works great. The service was excellent!!! I'm going back and having a hitch put on my other car soon. Thank you.

Everything was perfect.! Nice paint, package, and fast shipping.! Im satisfied.!

Click to Enlarge

Easy ordering, fair pricing, prompt delivery...product arrived in excellent condition, very heavy duty drawbar for use with by 4ft x 8ft medium duty trailer.

Solid quality and workmanship.

Excellent customer service & support! Bought for my 2013 Honda Fit and plan to trailer my Yamaha Tenere motorcycle around North America! Very happy with hitch.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Typical quality of...VERY good!! Lol. I've pulled my small mc trailer numerous times with this hitch and NO issues!!!

I would give five stars but due to what looks like packaging problems the hitch came very marred and the coating chipping off.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Good and strong but not a great angle/height for my application so had to go to a straight line fit.

I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.

Click to Enlarge

Purchased for a Hyundai Elantra. After a 2" ball is mounted, there is about 7.5" from the top of the square shaft to the top of the ball. This is what was needed to get the center of the ball 18" off the ground for most U-hual trailers. This design has no plate edge protruding below the square shaft. This helps reduce scraping when going over bumps, which is an annoying issue with my other ball mount. I would have much preferred the euro ball mount, which has a nice 45' bend to avoid scraping, and a ball that will never vibrate loose, but one was not offered with this much rise. The ball mount is well made of solid steel, not a hollow tube. Finish quality is excellent. The mount does not come with the locking pin needed and so that must be ordered separately with the ball. Item was packed a little loose in the box and was clanking around with the other item I bought, but they did not get scratched up.

Click to Enlarge

Click to Enlarge

works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.

Click to Enlarge

This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.

Click to Enlarge

I was in need of a hitch higher than the standard 3 or 4 inch riser and spoke with Samatha B, after a couple of emails she found a 5 inch riser for my 1 1/4" receiver. Just what I needed and a happy customer. Received very quick and good sturdy quality. Thanks again!

3.5 stars. Product looks like it should perform as advertised, but it arrived with several chips in the paint. This is most likely due to improper surface preparation and cleaning before the powder coat was applied. As you can see in the photos, there is already some surface rust on some of the areas, including the hole for the hitch pin. Ultimately the paint will get scratched up from use, but it would be nice to see some extra attention to detail from the factory.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Works perfectly for me. I use it to tow a motorcycle trailer behind my Mini Cooper with a concealed hitch so I need the extra length to clear the bumper. No complaints.

Excellent quality, solid steel bar and wields are excellent. The black coating is heavy and well applied. I’m Very happy with this product!

I needed to tow a trailer with a 2" ball. My original ball mount has a 1 7/8" ball installed. I had previously tried to change a ball on a hitch and destroyed the nut and damaged the underside of the ball mount. The lock washer had done a great job in keeping the nut from coming off. I dreaded trying to remove my 1 7/8" ball to install a new one that I would only use once. I decided to buy a new ball mount and mount the new 2" ball. This ball mount is so inexpensive that I realized I could have both ball sizes permanently mounted for use in either ball size.

I wasn't sure what type of ball mount I needed for my new Mazda CX-9, so I had to call a representative. The first time I called, the very knowledgeable gentlemen told me exactly how to measure my SUV to figure out the drop I needed. I called back the next day and talked to a lady who helped me figure out exactly what I needed. This is my second purchase from etrailer. The first was a hitch for my old Honda Odyssey, which was also a great experience. The employees are so helpful, the video tutorials on the web site are fantastic and the prices are great. etrailer.com is the first place I go to look for trailer and towing supplies!

I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!

Click to Enlarge

Drawbar looks great and will be using in next two days. Thanks!

This is the correct towbar for a Toyota Prius C. The towbars that are available from U-haul (3 1/8") and other hardware stores are too low to the ground for most trailers. I tow my Harley Dyna on a motorcycle trailer behind my Prius C with no problem. Save yourself the grief. I bought three readibly available tow bars until I found the right one. The 5" rise, 10" long works perfectly. This is an incredibly strong drawbar.

Click to Enlarge

Worked perfectly Did have to grind off the paint and a nit of metal to fit in the reciever though.

This is a great product. I really appreciate the quality. This was also a car I was having difficulty finding a trailer hitch for. So thanks again for a good product.

Click to Enlarge

I got a hitch for my Honda accord it was extremely easy to install took less time than they estimate after I installed it I bought a trailer and have hauled various things already with no problem I would recommend e trailer to anyone

Click to Enlarge

Click to Enlarge

I have a 2022 VW ID.4 AWD with factory installed receiver. This drawbar is 1/4" longer than VW recommends, but in rise orientation the length is required to clear the bumper. I ordered a shorter Curt drawbar but found it could not be installed in rise orientation because it hits the bumper before the pin hole is aligned. Both the shorter and this Curt drawbar fit fine in drop position, but were very tight in rise. I had to sand down the paint and file the corners to make the Curt fit easily so that it could be inserted and removed from the receiver by hand. I can't say whether this is a VW or Curt issue.

I highly recommend etrailer hitch and wiring harness They were both easy to install. The Prius pull the motorcycle camping trailer very well. You would not even know it was hooked to the car

Click to Enlarge

Click to Enlarge

Click to Enlarge