# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
GOOD QUALITY
# 2
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
EXACT AND FAST
I've made several purchases from e-trailer.com and have had excellent service and quick delivery. The front hitch was difficult to mount because the straps welded to the 1/2 inch nut weren't quite long enough to catch the thru bolt. I had a fairly hard time lining the nut up but was able to do it.
# 3
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
this hitch is great. i needed a longer ball mount to give me more room between my trailer jack and spare tire on the tail gate of my jeep wrangler. it is very hard to find a extra long ball mount. i found etrailer has them and a lot of other fine products.
# 4
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
EXACT AND FAST
The D-26 is just the right length for my 2008 Jeep Wrangler. The 32in spare tire doesn't get in the way of the hitch even with 3/4" rise. yay
# 5
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
Excellent product - very strong and secure! Does not, however, fit my 2016 Jeep Wrangler Unlimited. It is about 3.5 inches too short to clear the spare, and about that much too tall to go under the spare.
Hitch was as expected... appreciate the extra communication by etrailer.
# 6
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 7
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
EXACT AND FAST
Excellent quality. Made in USA
# 8
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.
What our customers are saying:
"I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future."