# 1
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
A perfect addition to my 3500 Dodge Ram Dually! Very excited to have found this product and the ease of installing into the frame and still have the tow hook capability. I started with attempting a solo install, however after successfully loosening 3 of 4 bolts, the 4th one (upper inside) was not gonna happen as it was very challenging with only 2 hands. Once I recruited an extra pair, the install went pretty smooth. It looks great.
This front receiver was used on my RAM3500. The installation video showed it being installed on another RAM3500, so I felt secure in purchasing it, but after using it to push my 8000lb trailer into it's resting place for the summer, I quickly found out it is under-rated. Tongue load goes to 900lbs which is apparently not the tongue weight of my trailer, when pushing up hill. The receiver flexed so much that I thought it was going to break or crack- it did place a significant dent in my bumper. Long story short, reconsider this receiver. Not pleased at all. This trailer is not a heavy load but maybe when pushing up a slight grade. Not sure what to do now since the install was a huge nosebleed.
# 2
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
It was easy to install and we use it all the time. Does its job smoothly every time
Seems nice and solid, should be strong enough to haul my 425lb motorcycle + 60lb carrier. Based on some of the reviews about what a pain it was to install I decided not to mess with it and take it to a hitch shop. They confirmed some of the complaints I read here so it was money well spent.
# 3
EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The hitch arrived quickly but unfortunately, as mentioned in other reviews, the shipping carton was damaged and parts were leaking out all over my driveway as the UPS guy brought it to the door. We gathered parts from the UPS truck and the driveway but some critical parts were missing (mount plates, spacers). I talked to Kennica C. at Etrailer about the missing parts and she was very kind and helpful but until I get these parts I can't mount the thing so we'll see how that goes. Seems that after all the trouble with packaging they would modify their packing procedure.
The fit and finish (on the truck) is damn near perfect. However the pin hole is about 1/2” further back than standard pin holes for hitches. I purchased this for the sole purpose of putting a hitch mounted winch on it. With the pin hole set 1/2” back the pin hole will not match up, I’m not sure how many other accessories this will affect. If this can be corrected and a proper pin hole placed hitch can be sent to replace this one I could give this product all 5 stars. As this hitch requires modifying the plastic shrouds I cannot remove it now as it supports those plastic pieces.
# 4
EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Just what I needed. The hitch fit perfectly, all parts were there and the installation instructions were very clear.
# 5
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Just what I was looking for. Thank you.
I ordered these two, front and rear for a 1990 GEO Tracker 4 wheel drive that I am rebuilding. I believed they would fit, I finally got around to mounting them and they don't fit, to large. I think I have had them to long to return them.
# 6
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Needed a front hitch for a 2006 Ridgeline Honda truck. I found it on etrailer.com and a better price for same hitch on another online store. As I talked with the customer service agent, I was also offered a discount which was quite a surprise. Shipping was very fast. Had it installed on my truck so I could attach a mounting hitch and snow blade. I am extremely happy with this hitch and etrailer.com.
They asked for a review a year later, AWESOME! I love the front mount on my '13 Ridgeline for a snowsport "floating plow" I bought thru AgriCover. My Ridgeline plows the whole neighborhood now!!!
# 7
EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Bolted right up to my 2019 F-250. Looks like it's going to work perfect to haul my E-bike rack. I might have to use a dual receiver hitch to drop the rack down for better visibility while driving. That's to be determined. I'd highly recommend the Eco Hitch!!
Fits 2021 F350 Diesel but with extensive mods to the Plastic Insert. 5 stars for weight ratings and overall build quality. 3 stars for installation hassle bc the plastic insert that needs to be slotted in my case needed to be cut back significantly and bracketry added which took extra time. Wish it came with 2 extra fender washers and a heads-up that the insert might need extra mods and brackets (see below). Did not have to move any coolers or cooling lines. 4 stars overall. Notes from the install. 1. Marked bumper brackets and supports to know exactly where it was installed by the factory. (Mine was off-center left/right by 1/4 inch so I centered it before cutting the slot in the plastic insert.) 2. Consider building some stands to help with the bumper removal/install and hitch install. Made a simple stand low enough to support the bumper and added blocks to install the hitch. (Also removed the front skirt before bumper removal.) 3. As other reviewers stated, had to shim one side of the hitch with 2 of the supplied fender washers as it was narrow by that amount. Had to purchase 2 additional fender washers. 4. Since other reviewers mentioned the slotting instructions needed improvement, more or less reviewed those and took them as recommendations. After hitch installation, test fit the bumper without the plastic insert. Then measured to the hitch. Then removed the bumper, installed the insert, and transferred the measurements to the plastic insert. 5. Found out during test fit after the slot was cut that the lower, back of the slotted insert had to be completely cut-off to fit. The insert needed to be flexed under the hitch so that the bumper to go back to the original position (see picture with notes). That flex would then warp the visible part of the plastic insert. Therefore, the section interfering was completely removed. Installed some brackets to support the lower section. The brackets proved to work well. That the hitch is stout, up high, and hidden is a plus. Will have to build or purchase a hitch adapter to drop the hitch about 7 inches for one of my uses but don't mind doing that. I recommend this hitch but keep in mind you might have the same installation challenges.
# 8
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The quality and fit is exceptional. So much so that this is the third hitch assembly I've purchased and installed. This one was for my brother in-laws 1999 F350. I also put a 10k winch on a slider that works perfectly with this assembly. Other vehicles I purchased and installed assemblies on are a 2011 F350 and a 2016 Class C motorhome. Very happy.
Great receiver. Didn't actually fit my truck's front bumper, but I was able to make some spacers to get it mounted. Works great for the mounting spot for a rig that holds my kayak on top of the truck.
# 9
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I got the hitch and made a appointment to have it put on. That fell through so I decided to tackle it myself. It was extremely easy, my wife helped hold it in place while I got the bolts started. I use the hitch which I install in the front of my 2500 Ram to haul my ebikes on a bike rack. Works excellent.
The hitch has done exactly what I had bought it for: to hold an adjustable, vertical T-bar at the front of my truck for supporting long cargo like canoes, extension ladders. As the need arises I'm sure it will work fine as a hitch for backing wagons into sheds, etc. But the need hasn't presented itself yet. The only unusual trait I've seen is that the hitch doesn't set perfectly level, in the same plane with the truck. The mounting holes, both in the truck frame and the hitch, left no room for adjusting, but the hitch works as it is and I'm satisfied.
# 10
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer
im very satisfied with my front receiver. ive used it as a recovery point,to move trailers, and as a mount for bike rack and cargo holder. if i had a winch platethat would be very handy too. etrailerhad a fair price, quick shipping, and overall great customer service. i would use them again andrecommend to a friend as well.
# 11
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I have had this hitch installed for just over a year now on my '99 2-door Tahoe. The install was pretty straight forward, and the hitch itself has held up quite well through a year's worth of abuse. I use it to run my bike rack out the front; the receiver protrudes just below the factory front bumper, maximizing ground clearance when adding length to the front of the vehicle. And as you can see, the kit comes with two sets of hardware in case you want to maintain the factory tow hooks like I have.
Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.
# 12
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Added to use with a front winch. The install was not too difficult and the included instructions were spot-on. On my F250, the front tow hooks add to the strength of holding the hitch to the frame. On the F250 you do lose the OEM fog light location, but I used the wiring to add/relocate after-market fog lights. The set up has already proven helpful, pulling me out of a snow back while plowing. Just what I needed for some summer off road camping as well.
I chose this product because it was among the more inexpensive front hitches I could find. I plan to build a t-bar for it and use it in conjunction with a homemade headache rack to carry 16 foot garage doors. Like other reviews and vids I have found, the bolt up is hard. I reversed the bolts and use the new ones on the outside, as well as removing my grill. My truck is a 2003 - so not much room like the 2008 and newer trucks.
# 13
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.
I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~
# 14
EcoHitch Invisi Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Review for truck front hitch receiver I finally Installed the front receiver hitch today, I pulled it out of its package and found all parts wrapped to the receiver hitch good call as there was a hole in the box. The license plate holder received some damage it was bent some. Installation. I reviews the video prior and read the instructions. Had to purchase a 4 inch hole saw and a torque wrench that added to the cost of the hitch. Installation was for the most part straight forward, when the video cuts from shot to shot I now know all the cussing and swearing are done during that time as it’s very difficulty to get the hitch in over/under the exiting hardware, solo installer took me 3.45 hrs to install, tight fit under the truck to maneuver under the truck. Bolts back into original tow hooks was a total Pain in the A$$ trying to hold up the hitch and the hooks while trying to maneuver the hold back in. (Had to take it out as I inserted on the wrong side) I will say that installation is doable by novice front yard mechanic but with a difficulty of 7 out of 10, trying to get the bolts torqued to specs is difficult due to clearance and angle of the bolts. Make sure you have deep well sockets because the new bolts for the hitch and long and a standard size socket will not be able to grip the nut as you tighten it down to specs. Put the bike rack on the hitch receiver and found that the hole that we drilled out to put the hitch in is not big enough. The bolt for the hitch goes in from the right and there was barely enough room to get it in the hole, used a wrench to tighten it but it was slow going, the other issue was that on the left side there is a hitch lock I struggled to get it on, but then could not reach in to remove the key. So final outcome was I had to drill out another 4 inch section of the bumper to get to the key. If your hitch has a bolt on bike rack like the swagman e-bike rack you want it to be secure so the bolt is a must this option may not be the best option. The bikes block the headlights so no night driving with the bikes on the rack. The handlebars need to be folded down otherwise the bikes will ride too high on the front and obstruct your vision. If I had to do it again I would have gotten the hitch that is lower and would not have to drill out my bumper, and it would have given me more visual clearance. I did take a shot drive with the bikes in front it will take a bit to get used to them being in the front as well as making wide turns while towing the RV that I don’t take out the car in front of me.
My friend installed the hitch and I helped . But mostly by staying out of his way!?? Everything worked out perfectly!!! Thank Y’all for the Great Service
# 15
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Road tested 4000 miles & off-road, Solid, Great ! I always wanted a front hitch, it is rad ! We had a great experience across the board. Ordered the front hitch mount and had a mechanic (Weld Tech/San Diego) install it, because they already had our van to install their lift kit. They charged me one hour labor. I can see that it fits well and is solid. We went on a 4000 mile adventure with a small motorcycle on the front hitch. etrailer has been a good source for for a few things now.
I own a 2003 Ford E-450 RV cutaway and wanted a front hitch to carry our bicycles since our rear hitch is used for a trailer. I originally tried to mount the equivalent Curt front hitch, because of its cheaper cost, onto the vehicle. However, the Curt hitch wouldn't work because it can't adequately accommodate the slight downward hump in the truck's frame. This hump can barely be seen between the two hitch mounting bolts. The hump is on both the left and right side frame rails on my vehicle. If your frame is not totally flat (has even a small hump) you cannot use the Curt hitch. The Curt's small indentation on its mounting flange will not adequately accommodate the frame's hump. This Draw-Tite hitch, 65001, mounted perfectly on my vehicle and the installation procedures I used were exactly as depicted in the etrailer video for the E350 van. In the video, the technician uses a rotary file to expand the rearward holes to allow the insertion of the bolts. I had to do the same thing and bought a rotary file for my drill at my local home improvement store for less than $3. I did not have to use the rotary file on the forward holes. In addition, I have the larger Roadmaster front sway bar and steering stabilizer and as you can tell in the photo, there is plenty of room for the hitch.
# 16
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Very easy to install. works great for bike rack and generator box.
After struggling with the answering menu, Steve Z. was instrumental in locating a hitch to fit my van which was not specifically identified in any data search. Weird year, 2005, of popular Chevy Express van, my luck! Using manufacturers dimensions I purchased #31016 on 12/21 and it arrived on 12/24. It's a very well built, USA built, unit. It arrived rapidly, but was missing half of the mounting hardware. The remainder of the hardware was rolling around in the box. Zip lock baggie ripped apart spilling them. I used a hydraulic jack to elevate hitch into place, and an additional jack to push the drill up to drill the 6 mounting holes necessary. No factory hole alignment. All the nuts for the bolts were lost in transit, but by a Christmas day miracle, I found 2 metric nuts to fit supplied bolts that survived the delivery. I will acquire, and install remaining missing 4 tomorrow. The installation went smooth and easy using this technique. It took around 3 hours with much of the time searching for hardware.' Thanks Steve Z. and etrailer. .
# 17
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Needed a front receiver to put a bike rack on my 2015 Ford F-350 (2WD) for use with my slide-in camper. Price on the details page I was viewing changed overnight when I went to place my order, but etrailer honored the earlier price. Order was placed 6/12 with a 3-5 days estimated delivery. It arrived on 6/14. Very fast service & shipping! Installation took me about 3 hours, working alone & without power tools and a pause to re-view the installation video. My truck did not have the brackets referenced for possible removal. Would be nice if video showed how one installs the front bolts with the limited accessibility between frame and bumper that I had in to 2015 F-350, with the installed tow hooks. Front left nut had limited clearance between frame, which affected my ability to use a socket and torque wrench. Finished installation provides about 9" ground clearance and requires about 3" hitch length to clear the bumper and grill. Otherwise, installation was simple, pretty much as described in the 2012 Ford video.
I plan on installing it tomorrow, however first impressions are not good. The box it item was shipped in was extremely damaged. Torn, ripped and taped up on all sides. The delivery person said that due to the sharp edges and the face it wasn't secured in the box (lose) led to the damage. It appears the item was not packaged properly. I just hope all the parts are there. More to follow.
# 18
EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Mounted it yesterday and it fit like glove on my 22 3500 chevy. Easy to do and only took a couple hours.
Super fast, free delivery. Box came in damaged, but the product was undamaged and complete. Installation instructions and video were spot on. Currently set up for a 12000 lb. inline pull winch, but the options are almost limitless. I'll possibly install a step to make access easier for under the hood work. As always, thanks etrailer.com.
# 19
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This was one of the easiest accessories I’ve installed on my Tundra. It is a front receiver hitch so I don’t use it very often. Mostly just for bike racks when towing a trailer, but when you need it you need it.
Straight forward and perfect fit on my 2008 Toyota Tundra!!
# 20
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Fits perfect and works just as I needed it to. I use it for my SnowSport plow set-up on a 2022 Gladiator Sport Max Tow. I’ve been using front receivers for this same plow for the last 24 years. It’s been used on 5 different trucks and this front receiver mount plow is the BEST. *** When installing on a Gladiator(possibly the Wrangler as well), the front plastic trim below the bumper needs to be cut for receiver clearance. I wanted a tight and “factory looking” install, so I took my time with a vibrating cutter and very sharp utility knife. After trying to put it back in place, the hole is not just square, it’s shaped more like. “T”. I suggest you make small adjustments/cuts as you go forward. It may take several times fitting and cutting to get it right and tight, but in the end it does look like it came that way from JEEP. On the Max Tow package, there is also a metal skid plate that does not get reinstalled. Unfortunately that piece is where the back of the plastic fascia mounts. I ended up securing it with some long heavy-duty zip-ties and it’s worked well for a year now. Just an FYI for those installing the same receiver on their same vehicle.
Installed real easy. Cuttingbthe plastic rock guard was the hardest part.
What our customers are saying:
"very easy to shop"