# 1
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
Great product and works well.
The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.
# 2
Draw-Tite Ball Mount for 2-1/2" Hitches - 1-1/2" Rise, 3" Drop - 10" Long - 18K
Well the first one was lost in shipping so I had to buy something local but I will definitely be using this one instead. It is MUCH beefier then the 14K one I picked up locally.
I have a truck with a class 5 hitch. Using the 2" to 2 1/2" adapter had a lot of play in it and this ball mount removed that play. The truck and me won't bounce around so much. Thanks for the great deal and fast shipping. Will be shopping with you again. Thanks again.
# 3
Curt Ball Mount for 2" Hitches - 5" Rise, 6-1/8" Drop - 9-3/8" Long - 10,000 lbs
ball mount had a nice coating on it before shipping. it was put loose in the huge receiver box. bouncing around loose it punched a few holes in the box and got a number of chips from hitting the receiver. it made the same damage to the receiver as well. this is too bad. I went with etrailer due to great selection and install info. people shipping just don't seem to care about the product. it would have taken veary little to package this so it would not damage other items, but no effort was made to ensure shipping would not cause damage.
Just what I needed.
# 4
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Meaty
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 5
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 6
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
Great product and works well.
The one foot ball mount works great on a 2014 Chevrolet Silverado work truck(no lift kit). We use it for a one axle, lawn care/utility trailer. It is used at least half the work week and has held up for a year. It may not be a good choice for a heavier trailer, but at that point we would also purchase a 2500 truck too. The mount helps clear the jack when the tailgate is opened with about 2 inches to spare.
# 7
Curt Class I Drawbar - 5/8" Rise, 1-1/4" Drop - 6-3/4" Long - 2,000 lbs
I wrote 2 days ago and haen't heardafom anyone so I guess you only want reviews-. Here is what I wrote Steve, the class 1 hitch doesn’t fit the trailer hitch either. I don’t understand the continuing problem with all of the Curt hitches we have tried including the last draw hitch you selected and shipped, which I now need to return after H. Idalia passes, I want to point out that I initiially ordered somewhere on line a Maxxhaul adapter so I could move my 2” trailer until I sell it and it fit perfectly. I NEVER expected to have so much trouble getting a ball hitch to fit the 1.25 hitch recommended by etrailer for my car. Aren’t you glad I am writing an email rather than make star comments? I know that someone writes these things for ‘you’ and you don’t necessarily do the hands on so please direct this problem to someone who is supposed to make these product directives and solve this $[XX] attractive trailer hitch problem so I can haul my lawnmower in for repairs when needed on my utility trailer designed for doing so. Doesn’t Drawtite have a ball hitch for level hauling a trailer rather than Curt which is too thick. The powers that be need to rethink OD (outside diameters) vs ID (inside diameters) in their trailer connectors, screw the rattling! PS don’t forget arrangements for the return of the recommended draw hitch.
Great price! Amazingly fast service! The drawbar was a very tight fit in the hitch until I scraped off some of the paint at the end; then it was perfect.
# 8
Curt Class III Ball Mount with 2-5/16" Ball - 2" Drop - 7,500 lbs
Great product and works well.
Everything arrived on time and well packaged. I installed a Curt hitch receiver to go with this ball mount. Installation for the hitch went exactly as described and was fairly simple for even a novice like me. Very pleased with etrailer.com and with Curt brand products in general. Couldn't be happier with the process from beginning to end. And the hitch looks and works great!
# 9
Curt Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-1/4" Long - 3,500 lbs
I would give five stars but due to what looks like packaging problems the hitch came very marred and the coating chipping off.
Good and strong but not a great angle/height for my application so had to go to a straight line fit.
# 10
Draw-Tite Ball Mount for 2" Hitches - 3" Rise, 4" Drop - 9-1/4" Long - 16K
Perfectly as described, Box was a heavy hitch and the box must have been damaged in shipping so it was a little delayed. You can't mess up a forged hitch it still is in excellent condition.
This simple ball mount will get the job done. It's a solid casting so it weighs a lot.
# 11
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise - 4" Drop - Extra-Long - 6,000 lbs
Meaty
I needed an extended ball mount for my new Jeep in order for my utility trailer tongue to clear the rear mounted spare tire. Item is as described on the web site and was received earlier than expected. etrailer has great customer service and is my number one go to place for towing and trailer supplies.
# 12
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
Great product and works well.
My order was missing installation parts, but the etrailer team were quick to correct the issue. Even without a lift, I was able to install the receiver and brake light cable quickly, thanks to their extensive video libray.
# 13
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 14
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Meaty
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
# 15
Curt Fusion Ball Mount for 2" Hitches - 1-7/8" Ball - 2" Rise - 5,000 lbs
Exactly what i ordered and it came fairly quickly! Im very happy worh everything!
# 16
Draw-Tite Ball Mount - 3/4" Rise, 2" Drop - 10-1/2" Long - 6,000 lbs
Meaty
I had previously purchased the etrailer hitch for my 2021 Ford Transit 150. It was a little short in length and the bumper prevented my current ball mount from working. As always, etrailer had the perfect solution. The Draw-Tite is well made and will now remain permanently with the van to be handy whenever the need arises.
# 17
Curt Class II Euro Style Drawbar with 2" Ball - 2-5/8" Rise - 3,500 lbs
It isbthe right size and helps with the height difference to make the trailer more even with the back end of my Accord.
Look and quality of the mount is awesome. Beefy in size as well. If using on my particular application, removal of rear diffuser is necessary. If they had extended it another inch it woulda been perfect. 2015 Audi a3 tdi. Wouldn’t let me add a third pic but it’s a finger tip space between the ball and bumper with diffuser removed.
# 18
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
Great product and works well.
I bought this on my knowledgeable brother's advice - he gave me the exact order number and link to buy from etrailer! I had it installed locally, without complications. I use my truck mostly to haul my horse or my friend's two donkeys in my 14-foot stock trailer. I have no complaints, the hitch does what it's supposed to do.
# 19
Channel Style Adjustable Ballmount - 2" & 2-5/16" Balls - 14,000 lbs
This hitch has worked out great for me over the last year. It’s very heavy duty and easy to adjust. I’ve hauled a 9,000 lb boat, long-distance on numerous occasions without issue. I also haul a landscape trailer on a daily basis weighing over 5,000lbs and haven’t had a single issue. Great hitch that was significantly cheaper than others and is very high quality. I’ve recommended it to several people and I wouldn’t hesitate to buy again. The only thing I would like to have now in a hitch is a tongue weight gauge, but it isn’t necessary.
This is a great hitch. Highly recommend this hitch. This is my second curt hitch, first one was on my ford f450 but unfortunately that one wouldn’t fit on my new truck, do to shank size.
# 20
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 2" Rise, 4" Drop - 7.5K
Nice combination to go with my front hitch for the F150.
dodge journey 2014 etrailer service excellent the hitch don't fit perfect with the spare tire other ways is pretty good if you tele out the spare tire you going to have a hard time to put them back etrailer sevicio es excelente la pieza no se acopla perfecto con la rueda de repuesto del resto se monta perfecto . si se retira la rueda de repuesto es muy dificil de poner de vuelta en el compartimento
What our customers are saying:
"In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!"