# 1
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Very pleased with the hitch. Very easy to Install. I did not remove the panel. I cut out a 2.5 inch X 12.5 inch section with the panel in place. Also I used a block of wood to move the exhaust pipe over a little. Took me about 30 minutes to install
I bought a hitch, stinger, ball and wiring harness for my 2004 Toyota Sienna. It was delivered fast, it was the right stuff, and it fit, just like it was supposed to. It really was as easy to install as it looked in your video. The video was immensely helpful too. The video showed me exactly what I needed to know to get my hitch installed correctly and it gave me the confidence to order online and do it myself. The only drawback is a loss of ground clearance but you warned me fair and square up front about that, so I can hardly complain. Thank you, that was a good investment.
# 2
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
This is exactly what was needed - we are pulling an 800 lb., single-axle lawn trailer and this setup is working very well. Installation took one afternoon and we were up and working the next day. THANK YOU!
Using this on my 2004 Toyota Sienna. Clears the bumper just fine and I like the easy functionality of changing the ball size. Sturdy construction!
# 3
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
Purchased this a a hedge on hoping I would have the right part, and in that respect, it worked (barely). After mounting a 76112, I found my hitch receiver tube to be at 12" above the ground. I will be using the 5" rise ball mount with the 2" ball as my ball mount to attach a rental trailer which would like the ball to be at 18". That leaves a 1 7/8 ball and additional hitch ball mount to come up with something creative to do with.
Product was a kit priced below the individual pieces to allow for trailering different pieces of equipment with differing heights and sizes hitch balls.
# 4
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
fits like a glove. works perfectly
I needed to tow a trailer with a 2" ball. My original ball mount has a 1 7/8" ball installed. I had previously tried to change a ball on a hitch and destroyed the nut and damaged the underside of the ball mount. The lock washer had done a great job in keeping the nut from coming off. I dreaded trying to remove my 1 7/8" ball to install a new one that I would only use once. I decided to buy a new ball mount and mount the new 2" ball. This ball mount is so inexpensive that I realized I could have both ball sizes permanently mounted for use in either ball size.
# 5
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
Came quicker than expected. All good .
Easy ordering, fair pricing, prompt delivery...product arrived in excellent condition, very heavy duty drawbar for use with by 4ft x 8ft medium duty trailer.
# 6
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Wonderful product. I had the hitch installed in 10 minutes. The wiring was a little more tricky because it required running a power wire all the way to the battery. I towed my trailer from Florida to Tennessee and back. Etrailer is still wonderful to deal with as they always have been in the past. My hitch came in a couple of days. I wouldn't think of ordering from any one else.
# 7
Convert-A-Ball Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 10,000 lbs
We used this on our 2012 Sienna AWD to pull the largest single axle closed top U-Haul trailer to move furniture and bikes 400 miles through the mountains of PA, WV, and VA with no trouble. I noticed less jerking from the hitch being transferred to our van than the last time I towed a trailer like this (though that was with a large sedan). Easy to install and seemed to have decent tolerances in regards to fit and finish. Definitely increased my confidence in towing with a light duty vehicle.
Good, very solid ball mount with just the extra rise I needed, 2 3/4", to get level trailer and good clearance for the trailer jack. But excessive shipping charges from etrailer, $[XX] for an $[XX] purchase. Found out to my cost later that [online vendor] would have shipped for free.
# 8
etrailer Ball Mount Kit - Extra-Long - 2-3/4" Rise or 4" Drop - 6,000 lbs
Thanks, Etrailer! The Ball Mount information is very helpful. This package works for my 2004 Sienna. Fast shipping. Happy with shopping experience!
Over all the ball mount kit is great. Getting two size ball mounts is convenient. Only complaint I have is the hairpin cotter pin fits somewhat loose. Not a great design there but the rest is great.
# 9
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
I had a great experience with etrailer.
This part came with the trailer hitch I purchased. It was very easy to transfer the ball from my 2" hitch and voila I am now ready to haul my trailer.
What our customers are saying:
"very easy to shop"