Summer Starts Here - Save up to 70%
# 1
Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs - 3" Long
My manufactured trailer did not have this type with a grease fitting. They wore out the bushing in no time. I really like the design and ability to lubricate the bushing.
I bought a set of these bolts to replace the hardware in the triple axle suspension of my toyhauler. I had read about the benefits of a wet bolt kit, and after finding two broken shackle plates on my camper, decided I too needed to be able to properly lubricate the moving parts. These were a perfect fit and replacement for my original bolts. At the time I installed them I hadn't read about orienting the hole in the bolt to the 3 or 9 o'clock to ease pumping grease through them. I put them in at whatever orientation they were in my hand, but had no problem pushing 3 - 4 pumps of chassis grease through the zerk. I was able to observe grease flow out of the spring eyes around every bolt, and all of the zerk fittings stayed firmly in place when I wrestled the grease gun nozzle on and off. There were a few bad reviews about these press on fittings falling out, but I didn't see any evidence of that. I am very pleased with this purchase, and enjoy the peace of mind that comes with knowing I can properly service my suspension and hopefully extend the life of all the components in the system.
# 2
U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles - 7-1/16" Long U-Bolts
Ordered a lot of parts for a dump trailer rebuild in Sept. Didn't install some of the final parts until Christmas break. THEY SENT COARSE THREAD NUTS INSTEAD OF FINE. I ruined 2 u-bolts and need all 16 fine thread nuts. I'm outside 60 days so I was told I'm on my own. I've spent $5k+ on etrailer. I'll find some place else.......
Exact replacement for original parts, easy install
# 3
Spring-Eye Bolt with Locknut for Slipper Springs - 3-1/2" Long
When I asked questions about my order they answered back quickly. Everything fit like it should. Yes time will tell if the springs are good.
Just what needed for my trailer. My old leaf springs were so rusted that I was one pot hole away from being broken down on the side of the road. These new ones are perfect.
# 4
Replacement U-Bolt with Nuts for 2" Wide, Square Trailer Axles - 9/16" Diameter
Ordering online is frustrating when your order gets denied for security purpose because payment method isn’t on file
Great product at fair price with fast delivery. Very pleased with the quality of that U-bolt
# 5
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 1-1/4" Rear
Well constructed
# 6
Dexter Bronze Bushings - Qty 4
Installed these with the Lippert AP wet bolt kit and Road Armor Shock Absorbing Equalizers. No more clanking and banging from the trailer going down the road and especially making tight turns.
I think Dexter, and by association, etrailer is selling junk parts. These are supposed to be "bronze" bushing. Even the Dexter packaging states "BRONZE". They ARE NOT bronze. They're cheap'azz steel bushings. Well I take that back they certainly aren't cheap. You can see in the first photo the old bronze bushing(these are Dexter original bushings that came with the HD wet bolt set-up several years ago) compared to the steel bushing now included in the HD shackle kit. Still doubting? The next photo shows the Dexter "BRONZE" bushing firmly held by a magnet. Still have doubts? How about a picture of the "BRONZE" bushings still in the Dexter packaging firmly attached to a magnet?
# 7
Nylon Bushing - 9/16" Inner Diameter, 11/16" Outer Diameter - 1-3/4" Long
Excellent service and quick delivery and great price, all looks good, thanks for helping me out with these items that I can't find around my area anymore,AES
Bushings quiet the trailer for a short period of time. Bushings wear out and squeaks return quicker than I expected.
# 8
1-1/2" Square Trailer U-Bolts (Qty 2)
I'm working on a 12 ft long 1957 Corvette trailer. Easy install, and perfect fit. I dropped the axle to gain 3".
I purchased these U bolts to upgrade the suspension on my trailer. I would get a a lot of trailer sway when I was towing my jet ski trailer. I bought the trailer used and never really looked at the springs. Unfortunately for me, There was nothing but one U bolt strapped diagonally across the spring. I'm no suspension expert but I knew this could NOT be safe. I did extensive research on trailer suspension. It was difficult to find parts for a 11/2 inch square axle. It was until I came across etrailer webpage. They had everything I required to upgrade and make my trailer safe to operate on the road. It was actually criminal what the person did to attach the original spring. I am greatful nothing ever happened while towing. Now with the new parts installed, I feel a lot better and my trailer does not sway anymore. I will definitely purchase my trailer needs from etrailer from now on. The pictures and videos make finding what I needed so much easier. The complete transaction from order to delivery was extremely efficient and the customer service is absolutely outstanding.
# 9
Equalizer for 2" Wide Slipper Springs - 12" Long - 7/8" Center Hole - Zinc Plated
The products I received were exceptional. First class and top of the line. But I had to ship them back. Was my own fault. I ordered the wrong size. . Even the process to order them and receiving them was a pleasure. Never had such and easy experience before when ordering products on line or on phone. Even shipping it back had me blown away at how easy. The sales rep, Lori, is ver profession and knowledgeable and very polite and courteous. Was a joy to deal with. Wish all companies were modeled like y’all’s.
Easy to install about 10 min start to finish. About 45 min to replace 4 thanks E trailer.
# 10
Curved Equalizer for 1-3/4" Wide Double-Eye Springs - 5-3/4" Long - 9/16" Center Hole
We have had great experience with eTrailer, These parts came in as described.
Great quality
# 11
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 7/8" Rear
I am sorry but I can not remember names but I talked with two very helpful ladies and could not have been happier with their assistance. Thanks again, the trailer build is going great.
My 6' x 10' landscape trailer was a homemade by a prior owner. While it was mostly constructed very well, the spring hangers were not correct. The spacing for the springs was also wrong, and it had very little fender clearance. There was also evidence that the spring U-bolts had contacted the frame on occasion. (I do not carry loads anywhere near the 3500# axle rating.) I added an extra set of holes on the front hangers in case the ride height proved to be too much, but I like the way it sits with the stock holes. I don't think I'll be utilizing the extra holes. This kit was just the ticket to increase the suspension travel and fender clearance on my landscape trailer. Now it "sits right"!
# 12
Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs - 2-1/4" Links
Got the kit today. Some of the nuts were oval and would not fit on the bolt of course. Now I have to go to box store and find nuts that fit! Not very good quality control!!
After all of the bad weather I was able to finish installing my new suspension system on my 1992 Lance Fifth Wheel. The task was much easier than I had anticipated. The instructional video you provide access to were a big help. Other than having to grind off a nut or two I had no difficulties (See attached photos). The 'list' that had developed on the fifth wheel is now resolved, and towing has already proven to be better.
# 13
CE Smith U-Bolt Kit for Mounting 2" Square Trailer Axles - 4-1/2" Long U-Bolts - Zinc
Arrived well packed and as advertised. I'm going to pull the azle out of the boat trailer and wanted to have this 'on hand' should I break some of my U bolts. I've bought from you before - always been happy, thanks
Worked perfect for mounting a storage box to my boat trailer.
# 14
Tandem-Axle Trailer Hangers for 1-3/4" Wide Double-Eye Springs - 3-1/4" Tall Front
Worked for what I needed. No issues so far.
These are the lippert brackets, I bought for spares just in case I was to break one in travels. Alsome product.
# 15
U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles - 5-1/2" Long U-Bolts
These did not fit my 3500 lb axle. It has been very difficult determining the correct size U-Bolts for my axle. It appears etrailer does not carry the size I need.
It is exactly as described. It seems solid. I also ordered the springs, and they appear to be solid as well. I look forward to continuing to do business with etrailer due to quality parts AND great customer service from the likes of Shawnee and the crew. Thank you!!!
# 16
CE Smith U-Bolt Kit for Mounting 2,000-lb, Round Trailer Axles - 4" Long U-Bolts - Zinc
Was a perfect fit for my trailer. The original axle was rated for 1500 lbs, was very hard to find bearings for and took weeks to get. After the other side failed, I decided to upgrade to a 2000 lb axle that had common hubs and bearings. No regrets.
U-bolt kit met all expectations. "Shiny" nuts and lock-washers screaming "offshore" sourcing. I replaced with eight (8) grade eights, probably made off shore as well. This will likely last the life of the trailer.
# 17
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 7/8" Rear
Excellent, had everything I needed and more for my trailer. Everything fit well!
This is a great kit! It included everything we needed to replace the old, worn-out brackets on our 6'x10' trailer. The directions were helpful and the brackets and hardware are nice and solid. We've had zero issues with the leaf springs (purchased on etrailer.com, also) or the brackets. Would definitely recommend!
# 18
Nylon Bushing - 9/16" Inner Diameter, 11/16" Outer Diameter - 2" Long
Fast shipping for regular mail and right product. I say a review from another purchaser that said to get these with the 2” X 10” and an 1/8 swan equalizers, good thing I ordered these also. After 25 yrs and about 2000 cords of firewood I rebuilt my Western Dump, everything fit perfectly. Thank You! Pictures-Worn out parts and new installed
Excellent spring quality for my custom motorcycle trailer. Arrived quickly. Glad I ordered a nylon bushing though. It didn't come with one for the open ended side and it should have.
# 19
Wet Equalizer Bolt with Castle Nut and Grease Zerk - 4-11/16" Long - 7/8" Diameter
We have had great experience with eTrailer, These parts came in as described.
very needed bolt
# 20
CE Smith Rear Hanger Bracket for Trailer Slipper Springs - Galvanized Steel - Bolt On - Qty 1
It works fine for my application.
Exactly what I needed. Great service and fast shipping. Thanks.
What our customers are saying:
"Excellent customer service. Best on-line ordering experience yet!"