Curved Equalizer for 1-3/4" Wide Double-Eye Springs - 5-3/4" Long - 9/16" Center Hole

Ask the Experts about this TruRyde Trailer Leaf Spring Suspension

• Replacement Upgraded Equalizer Kit for 13-104 Equalizer on Tandem Axle Trailer
  The correct replacement equalizer for your 13-104 is TruRyde Curved Equalizer # TREQ104. If you need the kit, you can use the Redline Tandem-Axle Trailer Equalizer Kit # AP233. The upgrade we offer for the 13-104 equalizer is the Dexter E-Z Flex Heavy Duty Rubber Suspension System - 5-5/8 Inch Equalizers # K71-652-00. These equalizers will replace the standard 13-104 equalizers and deliver smoother towing than standard equalizers. The rubber core will isolate and absorb damaging road...
  view full answer...
• Will Dexter E-Z Flex Suspension Kit Work With 31 Inch Axle Spacing
  Yes, you can use the Dexter E-Z Flex Suspension Kit # K71-652-00 with 31 inch axle spacing because these equalizers are a match for your current Equalizer # TREQ104. We have contacted Dexter about this previously and so long as the equalizers are the same measurements then you can use the suspension kits so it'll fit and work as a really nice upgrade for your trailer. I have added a link to a video review for you to check out as well of the Dexter E-Z Flex Suspension Kit # K71-652-00.
  view full answer...
• Would Too Long of Equalizer on Trailer Suspension Cause it to Be at Angle
  If your trailer is sitting perfectly level and the equalizer is sitting at an angle then yes I would agree you have too long of equalizers and would need to go with a shorter one like the part # TREQ104 which is 5-3/4 inches. Sometimes it's just a matter of the trailer not sitting level though.
  view full answer...
• What is the Weight Capacity of the Equalizer EQ-104
  There is no weight range for the Curved Equalizer part # TREQ104 or any standard equalizer for that matter. The weight capacity for trailer suspension is always going to be limited by its weakest component which is generally the axle. However, the above equalizer works with 1-3/4" wide leaf springs and there are 1-3/4" wide leaf springs available for 7,000 lb axles so I would not have any hesitation about uses these equalizers with up to a 7,000 lb axle. If the axle is above 7,000 lbs then...
  view full answer...
• Can Mor/Ryde LRE Suspension Hangers Be Replaced by Dexter EZ-Flex
  To replace your current Mor Ryde LRE system and go with an EZ-Flex system is possible, but you will need to replace the center hangers as well as the equalizers to do this. To pick out the correct equalizer will require you to measure the distance between the bolt holes from left to right on your current setup so that you can get the correct EZ Flex. If the distance is between 7-1/4 and 8-1/4 inches the part # K71-653-00 would be the correct equalizer. If the distance is between...
  view full answer...
• Best Upgrade for EQ104 Trailer Equalizer
  Yes, the E-Z Flex Heavy Duty Rubber Suspension System part # K71-652-00 will be a direct upgrade for the EQ104 Equalizer. The part I really like about the E-Z Flex is that in addition to the cushioned equalizer upgrade which will help smooth out the ride you get much thicker shackle straps which will be more durable and it comes with wet bolts for easy maintenance. Therefore, it's more of a complete suspension upgrade in relation to other kits that simply replace the equalizer.
  view full answer...
• Replacement for Rusted/Corroded Mor/Ryde LRE4100 Suspension System
  I do have an option for you but we do not carry any Mor/Ryde products so I would not have any replacement parts if that is what you are looking for. If there are components that are rusted or corroded then it would be best to just replace the entire system anyhow. The rubber cushioning has also likely worn down to the point where it is no longer effective. For replacement, I recommend the Dexter E-Z Flex Suspension Kit part # K71-652-00 for a 33" or part # K71-653-00 for a 35" axle spacing....
  view full answer...
• Do Trailer Suspension Equalizers Carry Weight Ratings
  Trailer suspension equalizers like # TREQ104 do not carry weight ratings but they are available in many different sizes. They will handle as much weight as any springs you'll be using with them. Part # TREQ104 measures 5-3/4-inches between its lower hole centers and kit # AP233 includes this same item among its component parts.
  view full answer...
• Can I Replace TREQ104 Equalizers With TREQ356 And What Difference Will It Make?
  You can replace the Curved Equalizer for 1-3/4" Wide Double-Eye Springs - 5-3/4" Long - 9/16" Center Hole, # TREQ104, with the Curved Equalizer for 1-3/4" Wide Double-Eye Springs - 6-1/8" Long - 9/16" Center Hole, # TREQ356. Even though you can replace these parts, moving to a longer equalizer will cause one axle to have a disproportional amount of weight on it. The smooth transfer of the impact won't be distributed as effectively which will cause a rougher ride without as good traction....
  view full answer...
• Cushioned Equalizer Recommendation to Replace TREQ104 Equalizers
  Best option for a cushioned equalizer kit to replace a equalizer part # TREQ104 would be the EZ Flex part # K71-652-00 which matches closely to the dimensions you have, does an excellent job cushioning the trailer suspension and comes with wet bolts like you are looking for.
  view full answer...
• Equalizer Kit Recommendation for Trailer Suspension that is 5-3/4 inches Long
  For an equalizer kit that includes equalizers that are 5-3/4 inches long we have the part # AP233. This kit includes straps that are 1-1/4 inch though so you might be better off with the equalizers # TREQ104 and then the straps part # TRSL256. For wet shackle bolts you'd want the part # 126B2.
  view full answer...
• Recommend Bushings Needed For TruRyde Curved Equalizer # TREQ104
  The item you ordered, TruRyde Curved Equalizer, part # TREQ104 comes with the bushings all ready to go. For replacement bushings for part # TREQ104, you will need the TruRyde Nylon Bushing, part # TRBU11566.
  view full answer...
• Heavy Duty Suspension Kit for 3-1/4 Inch Shackle Straps
  Having a 1 inch difference in the length of the shackle straps would be a pretty drastic change to the amount of articulation you get out of your suspension, so going with that kit wouldn't be advisable. We don't have a kit that uses longer heavy duty shackles, so you'd need to assemble the parts separately. • You'd need two of part # K71-358-00 • Two # TREQ104 equalizers • Two of # TRFA73Z916DLNZ shoulder bolts with nuts This will provide you the same kit, but with longer shackle...
  view full answer...
• Can 5-3/4 Inch Tandem Axle Equalizers be Replaced with 5-5/8 Inch Equalizers
  The Tandem-Axle Equalizer Kit, # AP233, will work as long as all other measurements are the same. Check that your shackle straps are 2-1/4 inches from center hole to center hole. The 5-3/4 inch long equalizer, # TREQ104, we carry is a direct replacement for the 5-5/8 inch long equalizer.
  view full answer...
• Using Taller Equalizer to Lift Trailer After Changing to Lower Mounting Holes on Hangers
  As you mentioned in your question, we typically recommend replacing existing hangers with taller ones to ensure you get the trailer lift you are wanting. But with that being said, in your particular application, that is what you will essentially be doing since you already adjusted the front and rear hangers to the lower mounting hole. Because of this, replacing the 2 inch tall Equalizer # TREQ104 with the 4 inch tall Equalizer # TREQ310 that you referenced will indeed lift your trailer...
  view full answer...
• Are Longer Shackle Straps Available to Replace the Ones In Trailer Suspension Hanger Kit AP233-H248
  The shackles including with trailer suspension hanger kit # AP233-H248 are 2-1/4 inches long measured from the center of one hole to the center of the other. The overall length is 3-1/2 inches. The longest shackles we have are 3-1/2 inches long (measuring between the holes on center) at 4-3/4 inches long overall, # TRSL350. I have included a link to the shackle straps we carry. There are several lengths available. If you just need the shackle straps and equalizers you could get them...
  view full answer...
• Does the Trailer Height Change when Using EZ Flex or Equa-Flex Equalizers
  The E-Z Flex Heavy Duty Rubber Suspension System # K71-652-00 is designed to fit in place of a specific equalizer, # TREQ104, which is 2 inches tall. When used to replace this equalizer or another with similar dimensions there is no height gained or lost. Adding height or reducing it cannot be achieved by just changing the equalizers. It would require replacing all of the suspension hangers as well to raise or lower the trailer equally and keep the suspension level. The comparable...
  view full answer...
• Replacement Leaf Springs, Equalizers, Shackle Straps, and Bolts for a 2002 Fleetwood Mallard 20N
  I have attached a parts list of everything you need including quantities below to replace the leaf springs, equalizers, shackles, and bolts on your 2002 Fleetwood Mallard 20N. Leaf Springs: Double-Eye Spring part # SP-216275 (4) Equalizers: Curved Equalizer part # TREQ104 (2) Shackle Strap: Shackle Strap part # TRSL225 (8) Wet Bolts: Step Wet Bolt part # 34007-187-00 (14) If you need any other parts or tools to complete the process please let me know and I would be happy...
  view full answer...
• What Axle Spacing will the Dexter Heavy-Duty Tandem-Axle Trailer Suspension Kit # K71-449-00 Fit
  The Dexter Heavy-Duty Tandem-Axle Trailer Suspension Kit # K71-449-00 that you referenced is designed for tandem axles with a 35 inch axle spacing and springs that are 1-3/4 inches in width. You would need to move the suspension hangers in the front and in the back on your trailer to use this kit. For an equalizer that is 5-3/4 inches from bolt hole center to bolt hole center from left to right you would want the part # TREQ104. For wet bolts you would need part # 126B2, for shackles...
  view full answer...
• Suspension Upgrades for Tandem 3,500 Pound Dexter Axles on a Jayco Travel Trailer
  E-Z Flex Heavy Duty Rubber Suspension System # K71-652-00 is designed for axle capacities up to 6,000 pounds. So if your measurements are close to those of this system you can use it. This system was designed to fit in place of equalizer # TREQ104 (13-104). Check your equalizers for the part number or just go by the measurements. Other option to improve the ride of the trailer is to use a shock kit such as # LC281255 for 2-3/8 inch diameter round axles or # LC281281 for 3 inch diameter...
  view full answer...
• Recommended E-Z Flex Equalizers To Replace TREQ104 Equalizers For Thunderbolt Toy Hauler
  We have just what you are looking for. The replacement equalizer you can use to replace the # TREQ104 is the Dexter Equalizers for E-Z Flex Heavy Duty Rubber Suspension, part # K71-654-00. The package contains two equalizers, bolts, and nuts.
  view full answer...
• Cushioned Equalizer Kit for a Tandem Axle Trailer Trailer with 5200 Pound ALCO Axles
  You may be able to use the E-Z Flex kit # K71-652-00. This kit fits if the tandem axle spacing is 33 inches and if the equalizers are # TREQ104 or have the same measurements. The measurements can be seen in the picture I have included. The E-Z Flex equalizer will actually fit in place of 5-1/4 inch to 6-1/4 inch long equalizers.
  view full answer...
• Improving Suspension of Tandem Axle Trailer with 3,500 lb Axles
  While we have a good option to improve the ride of your 1999 Terry Lite 5th Wheel trailer, the E-Z Flex Heavy Duty Rubber Suspension System # K71-652-00 is specifically designed for replacing Equalizer # TREQ104 and 33 inch tandem axle spacing so it isn't going to be a fit for your application. Instead, to improve the ride quality of your trailer I highly recommend the Roadmaster Comfort Ride Shock Absorbers for Tandem Axle Trailers - 3,500-lb Axle # RM-2450. This kit is for 3,500...
  view full answer...
• Could Equa-Flex Cushioned Equalizers Fit 2018 Heartland Prowler LX25
  Most likely the Equa Flex equalizers part # LC279687 will fit your 2018 Heartland Prowler lx25 since they are designed to fit most applications. But you'll need to compare the dimensions of what you have to the picture I attached to make sure these are the same so they'll fit. The Never Fail hardware kit part # LC281285 then would work well with this.
  view full answer...
• Will Lippert EquaFlex Equalizers Work if they are Shorter than Existing Equalizers
  The standard sized equalizers on your trailer have the same dimensions as curved equalizer # TREQ104. A great option to use in place of this equalizer is the E-Z Flex Heavy Duty Rubber Suspension System # K71-652-00 which was designed to replace equalizers with the dimensions you have. Using he EquaFlex system would throw the suspension off level some but ultimately it would not be a problem since the amount it is off is so little. You could use longer shackles to compensate or longer...
  view full answer...
• Can E-Z Flex Suspension System Replace Trailer With Taller Equalizer
  The E-Z Flex Heavy Duty Rubber Suspension System # K71-652-00 are absolutely an upgrade in terms of ride, they absorb shock in a way that standard equalizers are simply incapable of doing though it is designed to specifically replace Equalizer # TREQ104, which is 2 inches tall and your equalizers are clearly taller. If you did want to use this kit you would need weld on a taller center hanger such as the Center Hanger for Double-Eye Springs - 5-7/16" Tall # 115919 to compensate for the...
  view full answer...
• Correct Equalizer for Rvison Trailbay 31BHSS Travel Trailer
  I'm assuming that your existing equalizer is 6-1/8 inches long, measured center hole to center hole. If this is the case, we don't offer an equalizer that's 6-1/8 by 2, but we can get you really close with part # TREQ104 which is 5-3/4 inch long by 2 inches tall. The 3/8 inch shorter equalizer will slightly change the angle of your shackle links, which will actually allow a bit more suspension articulation.
  view full answer...
• Can E-Z Flex Equalizer be Removed and Original Equalizer Put Back On
  It sounds like you want to remove the equalizer portion of the Dexter E-Z Flex Suspension Kit # K71-652-00 and replace it with your old one, which sounds like it is the Equalizer for 1-3/4" Wide Double-Eye Springs # TREQ104. To do this you will want to replace what I assume are the existing nylon bushings in your equalizer and add two of the Bronze Bushings - Qty. 4 # K71-291-00. I have added some links to videos for you to check out as well.
  view full answer...
• Dexter EZ Flex Kit for 2019 Winnebago 2401 RG to Replace TREQ104
  The replacement equalizer you can use to replace the # TREQ104 is the Dexter Equalizers for E-Z Flex Heavy Duty Rubber Suspension, part # K71-654-00. This is the correct size and capacity you'd need for your trailer to replace what you have currently.
  view full answer...
• Replacement Equalizers and Wet Bolt Kit For a Tandem Axle Utility Trailer
  Your tandem axle utility trailer will likely have an equalizer like the Curved Equalizer # TREQ104. These would have been held in place by 3" Shackle Bolts # 166081 and Nylon Bushings # 721590 and Shackle Links # LC122487 on the ends of the equalizer. The best upgrade you can do is to replace the equalizer and all mounting hardware with the Dexter E-Z Flex Suspension Kit # K71-652-00. This kit has an equalizer that is designed to replace the curved equalizer with a width of 5-1/4" to...
  view full answer...

Do you have a question about this Trailer Leaf Spring Suspension?