Most Popular 9000 lbs Line Pull for 2009 Ford F-150

This hitch is high quality and fit perfectly. Install was relatively easy. I needed this hitch because I tow a travel trailer and need to carry my bike rack and bikes as well. I can move the bike rack to my rear factory hitch when I'm not towing, very simple. The pictures show my truck / RV with my bike rack installed in the front hitch.

Click to Enlarge

Click to Enlarge

Click to Enlarge

This is the third Curt front receiver hitch I have used on vehicles. The hitch was good quality with clear instructions included. It definitely helped during installation that I had a friend and shop to do the install as the ends had to be spread a hair to slide around the frame rails. We had the hitch installed in about 20 minutes. The reason for the average rating is that this is supposed to fit the 2010 Ford F150 Raptor. Although it does fit, you cannot reinstall the skid plate without sever modifications and then, the skid plate would just be for looks. The end of the hitch also sits behind the bumper requiring me to purchase a hitch extension in order for me to install my receiver mounted winch. I bought the RM-071-1075 from etrailer in order to mount the winch. Recently I had to use the winch and had no issues with this set up doing a straight pull. When we tried to pull at a slight angle, I was afraid of exceeding the capacity of the hitch due to the extra leverage caused by the extension (big heavy Raptor on 37's buried in mud and snow). Overall I would have given the receiver hitch 5 stars if the description mentioned that there would be issues installing on a Raptor. I probably would have done a traditional bumper mounted winch but I like being able to move the winch front to back (which is how I ended getting out of the situation).

Click to Enlarge

Click to Enlarge

Thank gooness eTrailer was able to recommend a local hitch installer! Evidently somewhere along the line shipping or possibly the factory the receiver got "tweaked" and the installer couldn't easily line up the holes to install the bolts holding the receiver to the truck frame. I didn't ask about what type of "tuning" was required but suspect there were likely some hydraulics and chains involved. Great installer, without a lift and special "tuning tools" and experience, there's was NO WAY i could have installed the hitch with jack stands and conventional tools-thank you etrailer for sourcing local installers! Also I had to buy a separate ball and hitch as my rear hitch was significantly larger (and too lower in the front) when installed in the front receiver. Using a smaller hitch enabled me to easily move and disconnect from the trailer. Other than the unexpected "tweak" somewhere either in mfgr or likely shipping, I've been very pleased with the Draw-tite receiver. Excellent installation instructions with some clever installation methods.

Click to Enlarge

Click to Enlarge

UPS was rough on the box but everything still lined up without having to pry but was snug on the back bolts. Install was very straight forward and did it myself in my driveway in just about 90 minutes from pulling the air dam to putting tools away. Used my floor jack to support the hitch in the center and started with the front bolts on both sides and then pivoted the hitch into position for the back bolts and then snugged up all four mounting bolts to the 110-ftlbs torque spec. Hints. made sure that front of the hitch was just a a hair pointed up from level before tightening down all of the mounting bolts. I pulled the air dam completely off and then lined it back up in position lying on the hitch so I could marked it, so I knew exactly where I would need to trim it and then used my Dremel tool with a cutoff wheel to trim it to fit. Then bolted it back into position and was done. I'll try and update this post once I take some pictures other than the shipping box

Click to Enlarge

This thing is well built, it fit perfect, This will come in handy for my needs. Instructions are very clear. If I was to rate the install on a 1 to 10 scale it would be a 5. Fishing the bolts thru the frame with the wire provided was much easier than I expected. I do recommend this hitch.

the install went very good but i do have one suggestion and see if your maker can put a notch in the middle hole to look like the tow hook it would make the install way more user friendly also had a little problem with one of your bolts after i had fished it down the hole the treads were burred and the nut wouldn't go on all the way so i had to fish it back out what a pain that was but got it done and replaced with one of the other bolts that you supplied me with and it went on great. now i have a ? about the hitch height mine only sits up at about 11 inches and change will that work with your snowplows that say they need 13 inches or will i have to do something different? but thanks for the great turn around time in getting it here quick.

Click to Enlarge

I got to say I'm one of the picky shoppers. I must see all reviews thoroughly, check it out from every angle and see multiple pictures before even being convinced to buy something online. I'm a welder and I was thinking about fabricating my own. After considering all the time for mounting breaking ,the plates drilling slotted holes. Steel price and then powder coating. This right here was an absolute supreme option all the work is done guaranteed to fit. So I took the Gamble and bought it and are not disappointed with their quality. Just like everything says I put it together in 45 minutes me and my 13 year old son. It is quite heavy lifting overhead to bolt up. Recommend having another person help you lift one side while fastening the bolt. The hardest part was getting the bolt to go through the sq punch out with the spring coil wire attachment that pulls the bolt through the frame. End result I'm extremely happy I did not have to cut any plastics or modify anything on my truck whatsoever. My truck is a 2001 Ford F-150 four-wheel drive crew cab. Now I have me my 9,000 lb winch on the front of my truck.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Installed this hitch on my 2000 Ford F150 4x4. It fit perfectly. No facia needed to be removed and no frame drilling was necessary. I simply removed the tow hooks and skid plate and bolted up the hitch and reinstalled the tow hooks. I notched the edges of the skid plate to clear the hitch frame (small angle grinder worked fine for this) and reinstalled the skid plate. Installation was simple and straight forward. The attached pictures may be a little dark but I attempted to show the hitch tucked up against the factory facia.

Click to Enlarge

was sent a hitch for a 4 wheel drive when I ordered a hitch for a 2 wheel drive and company wants to charge $xx.xx to return after sending the wrong hitch. after contacting Nicole in chat mode she says they don't carry the 2 wheel drive hitch. so my only choice is to eat $xx.xx to return a defective product that did not fit my 1998 ford F-150 light duty 2 wheel drive

The trailer hitch itself is well made and overall excellent quality. The only reason it didn't get 5-stars is the same reason mentioned by many others. The directions leave something to be desired. A couple of extra diagrams would have made the job easier to figure out. That said, it was about a 2-hour install. One detail for my 2002 F-150, I would recommend removing the plastic bumper skirt. The extra 15-20 min to remove and reinstall it will save a significant amount of struggle trying to jam bolts and wires through the front of the frame rail, install spacers, and make the install much easier. Also, having an extra person to help hold the hitch in place while installing the bolts will make the job smoother. You can do it yourself, it's just more work and struggle. Overall, a great product. I'd buy it again.

Awsome product!!! I use this front mount hitch a lot, mostly surf fishing at the beach using an attachment to carry a large cooler and fishing rods. I also use a winch that attaches too. Thanks etrailer.com

Click to Enlarge

LOL!!! You want my opinion on this product? Well the first day was a four hour nightmare! The second day took 10 minutes to mount and tighten the bolts.. Here's why. The manufacturer gives you absolutely no instruction on how to align and raise the 40 plus pound hitch up and into place all the while dealing with a pivoting sway bar mount. Now remember, you have to align three separate hole patterns to get the mounting bolts on. Trying to do this "free hand" is impossible. BUT if you align the hitch mount on top of the sway bar mount aligning the holes up and clamping it in place with two small vice grips, then raise the two separate pieces together with a small floor jack centered to the assembly, it raises up directly in line with the frame mount holes. Presto..... your there.

This receiver performs well for both bicycle and motorcycle carriers. It is not obtrusive when not being used. It was easy to install with no drilling required (You do have to cut out the air dam.). I would have given 5 stars if would’ve fit a little higher. There was room for it to be at least an inch further off the ground. I ended up putting a 1 inch leveling kit on the front of my 2 wheel drive F150 and it turned out great and the truck looks better too

I am very pleased with this equipment. Bought it to carry two heavy E-bikes. Installation directions could have been clearer--but with the help of videos, I got it in just fine. Had to use a large crow bar to urge it in place though.

Click to Enlarge

Click to Enlarge

Just what I was looking for. Thank you.

I ordered these two, front and rear for a 1990 GEO Tracker 4 wheel drive that I am rebuilding. I believed they would fit, I finally got around to mounting them and they don't fit, to large. I think I have had them to long to return them.

We live just south of Buffalo and Put this on our '11 Honda Ridgeline with a snowsport plow and a week later it snowed, and snowed and snowed... 5 feet in 24 hours and it's still snowing.... It's not good.... It's AWESOME! Not one driveway or even our street is clear... Except ours. It was easy to put together , easy to install and works exactly like it's advertised! It's November and it paid for itself already. Communication with etrailer was exceptional. We could not be happier with the whole setup.

Click to Enlarge

Needed a front hitch for a 2006 Ridgeline Honda truck. I found it on etrailer.com and a better price for same hitch on another online store. As I talked with the customer service agent, I was also offered a discount which was quite a surprise. Shipping was very fast. Had it installed on my truck so I could attach a mounting hitch and snow blade. I am extremely happy with this hitch and etrailer.com.

I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~

Click to Enlarge

Click to Enlarge

Click to Enlarge

Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.

I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer

Click to Enlarge

im very satisfied with my front receiver. ive used it as a recovery point,to move trailers, and as a mount for bike rack and cargo holder. if i had a winch platethat would be very handy too. etrailerhad a fair price, quick shipping, and overall great customer service. i would use them again andrecommend to a friend as well.

I went with this hitch since I have an after market front bumper. I wasn’t sure if it was going to fit but since this hitch was a bolted connection it gave me 2 options to have a chance it would fit. One I received the package the box was damaged but all the hardware had been taken to the hitch, so everything was there. I installed the hitch by myself and took me about 2 hours but that was due to the aftermarket bumper and dealing with that hardware at the same time otherwise the install went smooth. Tha last phot is to show this hitch worked with this bumper.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Mounted this hitch about a year ago and really like it. We pull a fifth wheel camper so this affords us the ability to haul our bikes or kayaks(tall T stand) up front. Was easy to install and looks good to boot.

Click to Enlarge

Work great, was easy to install, instruction that it came with weren't great, but video online helped. Going to use it for a bike rack and Winch. There was some scratches on the hitch when I received it, I think you need to rethink you packaging, putting metal on metal and wrapping it Saran wrap just doesn't keep it from rubbing, I will have to touch it up. Thanks for the fast shipping.

Click to Enlarge

My front hitch for my 2008 Tacoma got to me within 3 days very fast service. I installed it in 30 minutes and was able to put the front skid plate back on without doing any other changes to it. Very good product. I will be using it to put my rod rack on front of truck to use it at the outer banks of North Carolina for surf fishing this coming fall. Thanks for a very good hitch.

Click to Enlarge

Click to Enlarge

This fit my Ford 2023 E-450 (cutaway) perfectly. I had measured the frame of previous year E-450’s and didn’t see any difference so I gambled and ordered the 65053 which fit. Installation was straight forward with modification and fitting of the splash guard taking 50% of the time. Fit and finish was good except at the front of the receiver itself. Unfortunately that’s the only two inches of the whole hitch that show and had weld splatter and sharp bits under the paint. This took a bit of filling to smooth out which I then repainted. Attached are photos installed on my 2023 E-450.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Easy installation, nice sturdy hitch that fits on the front of our C- Class RV to haul our electric bikes. Highly recommend it.

Click to Enlarge

Great customer service and product.

The quality and fit is exceptional. So much so that this is the third hitch assembly I've purchased and installed. This one was for my brother in-laws 1999 F350. I also put a 10k winch on a slider that works perfectly with this assembly. Other vehicles I purchased and installed assemblies on are a 2011 F350 and a 2016 Class C motorhome. Very happy.

After a year of having this on my truck I can say that I wish I did it sooner! The installation is easy as can be. The hitch is super handy as both a tow point and also as a kind of skid plate/bumper. I have contacted multiple ecology blocks and other objects in my truck, the hitch is the first thing to touch so nothing on the truck gets damaged! This is a super strong, affordable, and versatile addition to any vehicle!

Click to Enlarge

Click to Enlarge

Click to Enlarge

VERY Easy install - not quite centered but that's no biggie - Used it already to fine tune the travel trailer into it's tight parking space. Also will be used for carhauler/utility trailer parking and canoe hauling and bike hauling and winch mount - Multi use deal! ; )

Click to Enlarge

I had been waiting to find this Curt hitch on sale for a while. First off I get to keep the hooks that came with my 2004 Silverado Crew cab 2500HD 4x4. Then I removed two existing bolts and loosened a third on each hook. Using a floor jack lifted the hitch into place and threaded in the new bolts through the frame and into the hooks. The biggest problem I had was being able to reach the bolts into the side of the frame and hooks w/out removing the air dam. Looks GREAT!! I know some reviews have mentioned a reduction in ground clearance but my truck is not lifted and the clearance is nearly the same as the transmission skid plate installed by the factory. I sometimes need to get low hard to see trailers into tight spaces and I’m also looking to pick up a winch. Looking forward to many years of hard work.

Click to Enlarge

Unbelievable how clean the install is for this product!! I was certain I would have to do some cutting or drilling, however not a single cut or new hole required. The product fit like it was straight from the factory ... even with the existing front Grille Guard that I have on my truck!! I also appreciate the FAST shipping and customer service, as tracking info was emailed after the product shipped without requesting this info and the product arrived within the same week. I've already recommended etrailer to other landscapers on lawnsite.com, as we're always looking for front-mount solutions for spreaders and other landscape equipment.

Click to Enlarge

Click to Enlarge

Added to use with a front winch. The install was not too difficult and the included instructions were spot-on. On my F250, the front tow hooks add to the strength of holding the hitch to the frame. On the F250 you do lose the OEM fog light location, but I used the wiring to add/relocate after-market fog lights. The set up has already proven helpful, pulling me out of a snow back while plowing. Just what I needed for some summer off road camping as well.

Click to Enlarge

Click to Enlarge

Click to Enlarge

I have not installed the hitches on my truck but they look to be well made and will replace the OEM hitch just fine assuming it fits. I did lower the rating because of the shipping. BOTH hitches came by LTL UPS Freight and BOTH hitches were delivered out of their boxes. The had ripped through the side or end of cardboard box. UPS carried the hitches up to the garage and then placed the boxes over them. I am hopefully that all the hardware and instructions were delivered. After I get them installed in a couple weeks we'll see how the rest of the story goes.

Great product,easy installation and dealing with etrailer has been a real good experience.

Fits perfect and works just as I needed it to. I use it for my SnowSport plow set-up on a 2022 Gladiator Sport Max Tow. I’ve been using front receivers for this same plow for the last 24 years. It’s been used on 5 different trucks and this front receiver mount plow is the BEST. *** When installing on a Gladiator(possibly the Wrangler as well), the front plastic trim below the bumper needs to be cut for receiver clearance. I wanted a tight and “factory looking” install, so I took my time with a vibrating cutter and very sharp utility knife. After trying to put it back in place, the hole is not just square, it’s shaped more like. “T”. I suggest you make small adjustments/cuts as you go forward. It may take several times fitting and cutting to get it right and tight, but in the end it does look like it came that way from JEEP. On the Max Tow package, there is also a metal skid plate that does not get reinstalled. Unfortunately that piece is where the back of the plastic fascia mounts. I ended up securing it with some long heavy-duty zip-ties and it’s worked well for a year now. Just an FYI for those installing the same receiver on their same vehicle.

Click to Enlarge

Click to Enlarge

Product shipped and received on time. I'm very happy with the packaging. Hardware was included with instructions to install the hitches I purchased.