Most Popular Round Bars for 2005 Toyota Camry

This will be used on a 2015 Toyota Camry to carry a kayak both locally and to the beach. No problem with the installation, and had all the necessary parts. Tried it today and it worked beautifully. I especially appreciate the follow-up with the links to the video. I did need a little help on how to install the straps to the car. Product works great, and the customer service was excellent. Highly recommend the product and the company.

I installed these as soon as I got them and I’ve got to say, there are some extra holes for screws that are a tad misleading and the pieces that secure it to the cross bars don’t seem super secure. For reference, I do have Rhino Rack’s vortex crossbars so this should fit snug. The rubber tops were tough to get into place and I am worried they’ll snap when I go to remove my rack but Rhino Rack has yet to fail me with their products so I bet it’ll work out great!

Click to Enlarge

Great product and excellent customer service!

The product is of good construction but probably due to how it fits on my crossbars it needs additional support. The crossbars for my Honda Pilot are wide blade type and these racks seem more appropriate for narrower square type crossbars. Even with the rack fastened very tightly, the rack can twist back and forth. Last year on a trip across Montana the wind was pretty gusty and it caused the front one to pivot quite a bit and we had to pull off and apply a ratcheting strap over the kayak and under the factory rails to ensure it was held tight and wouldn't move again. This year on the same trip we had bad winds but had a roof rack mounted behind these racks giving it support on the tall side. We had to strap it real good to make sure it didn't move. If we hadn't had that additional support behind it and add'l straps we probably would have had more problems. I think if the top metal bracket had a wider channel to fit our crossbars it would be much more stable. The way it is now it just sandwiches 2 metal plates between my crossbar which allows it to pivot under stress.

Click to Enlarge

The product seems great but I have not figured out how to get it safely attached to my bars. I have an Agricover Adarac on the bed of my truck and the crossbars are 1-1/2 x 1-1/2 inches square. I thought this would work well since it's for up to 3-1/2 x 1-11/16" crossbars, but it isn't secure on these. I'm going to try and figure out an alternate method for attachment though. Thule Hull-a-port Pro's are the perfect (mounting) solution but don't seem to be made any longer.

Click to Enlarge

Great product and great customer service! Very easy to install, but I highly recommend to watch the installation video first. We used typical black office clips to clip the excess straps down since they came untangled when driving. Also, I recommend to purchase locks for the racks since we are concerned someone may steal them because they are so easy to take on and off.

After attempting to mount the individual rack pieces using the “burglar proof” button head screws with the pin in the recess and the short hex wrench with the hollowed out end I discovered that no real burglar would want the rack but would rather have the kayak so the first thing I did after spending 10 minutes trying to insert the hex into the button head screws with the pin inside the recess and attempting to turn the bolts and continually being obstructed by the support pieces and the paint interference on the bolt heads with trying to get the wrench into the recess I knew it was going to be a long frustrating process so I threw them away and purchased new button head stainless steel bolts and a 4mm extended handle hex wrench to turn them. Smartest thing I ever did. You not only have to mount the rack initially but then you have to put the kayak on the roof and remount all pieces again to fit your boat. All kayaks are different to one degree or another. Having to move the individual support and retighten them with the boat on the rack is even more difficult to do than the initial mounting with these “burglar proof” bolts and hex wrench and you will be happy you threw them away before you started the entire process. Try it for yourself at first and then go get the alternate ones. Worth the little investment and stainless steel will not rust away when you want to remove the rack system in the future. Once the rack is on your vehicle and kayak in rack the tie downs supplied are very good quality. Make sure you use the recommended tie down locations and directions, two kayak body ties and ties at front and rear. Due to numerous kayak hull designs it would be nice to have each support pod have a horizontal swivel built into it so it readily conforms to the hull shape. The overall quality of the system should be the last rack you will have to purchase. I only had issues with the supplied bolts and hex wrench. I gave this rack system a three star because of the bolts and hex tool and the individual pods not swiveling and I haven't at this point transported the kayak anywhere so I am waiting to see how it handles long trips with wind loads and constant loading and unloading performances.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Works great. I’m 5’6” and the pivoting cradles make for easy loading and off loading. I do need a stepping stool to install the carrier on the roof rack.

Arrived quickly and was very easy to assemble and attach to the roof of my Jeep. Now that I have the initial setup complete with the proper placement of the entire system, attaching and removing the kayaks will be a breeze. Will definitely make hauling our kayaks much easier and safer.

Click to Enlarge

I think the Thule Hulaport kayak racks are the best, most secure way to transport your kayaks. I had these on my Xterra and hauled two kayaks up to Cape Bretton park in Nova Scotia, Canada from Connecticut, USA no problem. We were even able to store gear in the kayaks for the trip. I’m so excited to have them for my Crosstrek. Highly recommend these!

Click to Enlarge

It's doing the job of securing my kayak to my rackless prius, at a fraction of the cost. However, the instructions included along with the straps did not work for me. I spent a considerable amount of time adjusting things: the red straps that are supposed to go over the boat and secure on the bars were not long enough. The blue straps are much longer, so I am using the red straps to secure the bars to the car, through the open doors and cinched inside the car. I am using the blue straps to reach over the boat, and I decided to feed those into the car too- feels more secure than to attach them to the bars on top. The black straps for front and back strapping don't work for my car in the way shown, I had to jerry-rig. Overall I have figured out how to make it work, and I'm glad I didn't spend $xxx.xx on a serious rack system.

Click to Enlarge

It's reliable and very easy to install. Trapped several different kayaks onto roof and driven long distance at top speed and no issue with kayak getting loose or moving around.

Click to Enlarge

Click to Enlarge

This kayak carrier works great with my factory Rav4 roof rack and 10' Tamarack Angler kayak. I did break one tightener knob but probably over-tightened it. And it was replaced for free. I can load and unload the kayak easily and it doesn't budge going down the freeway. I can even drive in and out of the garage with the kayak on the rack for easy storage hanging from the rafters.

Click to Enlarge

Installed this Thule Top Deck Rooftop Kayak Carrier System with tie onto our Thule Roof rack system. Easy to install and this will carry our handmade 17' Wooden Sea Kayak. Very well made.

We needed a better way to haul around 3 kayaks and after looking at a number of options, we settled on the Thule Stacker setup. Installation is simple and the stackers provide a sturdy option for hauling multiple kayaks. One of the best features is that they fold down when you don't need to use them. My shopping experience with etrailer was smooth and shipping was prompt.

Click to Enlarge

My wife uses these to carry two small kayaks in the roof of her Subaru. They work great and we very happy with the purchase. She also likes finding her car easier in the parking lots, even with the carriers folded down.

Click to Enlarge

I need replacements when a pair of Dockgrips was was lost or stolen. When others were stocked out, etrailer came through. Fast shipping and courteous service!

The Thule DockGlide Kayak Carrier and the Tie-Downs that came with it are a very functional High Quality Product. Once the DockGlide Carrier was properly positioned on the Cross bars it attached easily and solidly with the associated hardware. The Kayak slides on and off the Carrier very easily and is quite secure once properly tied down. I enjoy Kayaking and the DockGlide Kayak Carrier enables me to get where I want to go.

As all Thule products the Thule universally mounted canoe carrier is great. It came with all required items for safe and easy canoe transportation. There are two straps with pull to fasten for the canoe down, two tie down ropes for each end with nice pull tight and release mechanisms for the cord as well, along with two straps to fasten to the canoe ends used with the pull to tighten cords. The Chevy traverse cross bar had to have the plastic end caps removed for use with Thule canoe carrier. This was because my canoe took up the entire cross bar width to allow for Thule mounts. It is not a big deal to remove the plastic end caps. They only provide a finished stream lined look. Happy and Safe Canoeing

Click to Enlarge

Click to Enlarge

Click to Enlarge

After retiring my 1999 Chevy Silverado 4x4 pickup, I purchased a 2017 Subaru Outback as a replacement vehicle. To transport my 1981 17 foot QT17C Alumacraft canoe on the factory installed roof rack crossbars that came with the Outback, I selected the Thule Portage Canoe Carrier w/ Tie-Downs - Gunwale Brackets - Side Loading - TH819 to do the trick. With one previous transport of the canoe sitting directly on the Outback roof racks, I realized those Outback roof racks were not as durable as the racks on my truck so I sought an improvement to avoid future scuffing and scratching. I did some advance research online and couldn’t be more pleased with this purchase from etrailer.com. I now have a quality product at the right price and these gunwale brackets are a simple solution for this veteran canoe man. The padded brackets grip the canoe and stopped the scratches. The high-quality load straps are nice with the rubber pad that covers the buckle and they easily snug the canoe tight to the racks. I’m also impressed with the bow/stern tie downs that have a very nice ratchet and clip on one end and I secured the supplied hook with a bowline knot to the other end of the ¼ inch rope. The Outback did not have convenient anchor points on the front or back of the vehicle for tie down locations but I found a good solution there as well by ordering the Thule Bow/Stern Tie-Downs - Qty 2 - TH530. This works well with the tie downs I mentioned previously. One limitation to be aware of with the Subaru Outback roof racks and this product is the width of your canoe. My 17-footer measures 34 inches at its widest point at the portage yoke. I had to place the four brackets up tight against the inside roof mounting to achieve the spread and accommodate the canoe placement. The canoe ended up fitting like a glove on the padded brackets. When placing the strap to hold the canoe down to the crossbars, I ran the strap through the vehicles tie down points and then under the crossbars for added security. Total product installation time including securing the canoe can easily be achieved in approximately 20 minutes. I look forward to many more years of safe and happy canoeing. I give etrailer.com an excellent rating for the entire ordering and shipping process on top of the high level of satisfaction with the products I purchased through them. Their customer service and price ensured me that I’ll do more business with them in the future.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

I have (2) Wilderness Systems Pungo 120 kayaks and was looking for something better that the cheap J-Shape kayak holders that I purchased elsewhere. Unless you are tall enough to lift the kayaks and install them from the side, the loading of a kayak on it's side is unwieldy and somewhat frustrating to keep the kayak from flipping to a horizontal position. I am using the factory racks with crossbars on my 2006 Toyota Highlander. I was looking for a solution that would allow me to load 2 kayaks with the keel down. Using a large bath mat to protect the paint I was able to load the kayak by myself and I am 5'6". The one thing that they could improve is that the rubber pads on the wings are very tacky. Once that you set the kayak onto the wings, the kayak will not move back and forth. You will find it very hard to move the kayak front to back once it is set in the cradle. This is a good thing since the kayak could slide off should a strap fail. The Pungo 120 has multiple angles so the contact with the wings are very minimal. The rubber does keep it in place before strapping them down. Once you load the kayak onto the wings, it will stay where it is.. it is a kind of a struggle to move the kayak.. a solution is to throw large beach towel on the wings before loading your kayak and you can position the kayak with ease. Once you have centered your kayak, lift the kayak one end at a time and remove the towel. Bow and stern tie downs are necessary to completely secure your kayak. The wings are 28" across and will rise 6" above your crossbars that you attache them to.

Click to Enlarge

Click to Enlarge

Bought two sets for two boats. Installed on a 2020 Forester and will be able to carry two boats side by side. Sturdy racks and easy to assemble and install and will be easy to remove when not in use. They will also fit on truck racks so the ease of install/removal will be a real plus. Side by side mount on this vehicle required placing the racks a little more outboard than I like but should not cause any problems. I will strap the boats to the crossbars as suggested in the instructions for additional stability. PS. one set was returned merch. Got a better price and can't tell that it was ever out of the box. Yay me.

Click to Enlarge

Click to Enlarge

These pads worked well on our Yakima RailBar Crossbars- Item #Y00448-0449 that we also bought from etrailer around 2020/2021. Not sure if etrailer carries the exact Yakima Crossbars anymore, but think they have a similar model. Both the pads and crossbars work well to haul our kayak on our 2019 Subaru Forester. etrailer's customer service rocks! We had a lot of questions purchasing both items and they were great to talk to!

Click to Enlarge

Click to Enlarge

Click to Enlarge

The product came quickly and was so easy to install on my existing roof rails! It is absolutely perfect to fit many needs above and beyond my kayaks and paddle boards. They look so good on my new 2019 Jag F-Pace I might leave them on all the time.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

These work great and I was able to install them on the OEM rack for my truck. The only downside is that the threads for the clamp hang down a little too close to the roof for comfort.

I acquired a second kayak and needed a system to fit the factory racks on my 2011 Toyota RAV4. Etrailer.com has always had information on what fits and has always had the item needed for the job. I attached the Yakima BigStack to the top with ease, and, with one other person to hold the kayaks while I secured, tied two of them down for a long road trip to Northern Minnesota. The system worked just fine. The only caveat was in the configuration of multiple boats in the instructions. The diagram has two boats on the same side of the posts, however, I found it more secure to put one on either side ( other reviews of this product on different Internet sites have found similar results.) The boats made it through the trip with no shifting.

Worked great on our Subaru Crosstrek with factory crossbars. Loading very easy, and it was very secure, for our 2 kayaks. The Yakima Big Sticks are easy to install/setup and take off. Very happy with our investment,

I love this rack! I don't think I'll ever take it off my car. Cool and functional. I've used it for my snowboard in the winter and my surfboard and camping gear in the summer.

Click to Enlarge

The product very well made.. I have owned for a year now.. stays in place.. protects my paddle board

Click to Enlarge

The product arrived in a timely manner with specific information as to where it was all of the time. There was a credit card issue in the initial order and when I called I was pleasantly surprised to talk with a person who expressed sincere interest in my experience with the company The product is of high quality and is heavy duty, something which I was concerned about. It exceeded my expectations.

Product arrived in timely fashion as advertised. Easy to install. Perfect for my two kayaks.

Wry disappointed in such an expensive rack and kayak carrier. It is extremely difficult to reach the carrier to place two kayaks. We are very uncomfortable transporting the kayaks for longer and highway travel. I would not recommend these to others. We likely will purchase something other in the future. I’d rather put the kayak in a car or pickup truck that they would fit in.

We bought this Kayak rack for my mom to put on her 2016 Jeep Grand Cherokee so her and my dad could haul their kayaks easier. The mounting hardware was a little tricky at first but once we figured it out, it wasn't bad at all. It holds the kayaks in place nicely. Had no issues with them getting loose or moving around. Seems to be built well and they're very happy with it so far.