The Hughes Autoformers Safe View Smart Power Inlet part # HU27VR is a replacement power inlet for your trailer. I have attached for you below the steps you'll need to take for the power inlet to be effective against protecting your trailer.
Turn off the main breakers on your RV and at the shore power source
Plug in your shore power cable, connecting your RV to the camps outlet
Turn on the main breaker at the shore power pedestal, then check the LEDs on your inlet
If all indicator lights... view full answer...
Hello Roger, thanks for reaching out. We do have a variety of 20 amp and 50 amp power inlets. I am not seeing we have anything with a 90 degree connection on the back though. Everything would plug straight into the back like the SmartPlug RV Power Inlet and Connector # SM87FR. view full answer...
You will indeed need to replace the entire box of the automatic transfer switch as opposed to just the switch portion. There are two options for this, either a 30 amp or 50 amp transfer switch:
- 30 Amp: Furrion Automatic Transfer Switch # F30ATS
- 50 Amp: Furrion Automatic Transfer Switch # F50ATS view full answer...
The SmartPlug RV Power Inlet # SM97FR would be wired to the trailer and would be paired with a SmartPlug power cord, like part # SM59FR, that has a matching connection for the inlet and a standard 30 amp connector on the other end to connect to the shore power pedestal. view full answer...
As far as the inlet plug you need to run your air conditioner unit, you will first need to install the Epicord 30 Amp Twist Lock Power Inlet - Black # 277-000138. Once the inlet is installed, you will be able to use a 30-amp plug like the Mighty Cord RV Power Cord - 30 Amps - 25' Long # A10-3025ED. You will then be able to connect those components to a 30-amp shore power source.
I went ahead and attached a video of the installation of the inlet if you need help. view full answer...
Yes, the installation of a power inlet such as the Furrion Marine Power Inlet - 30 Amp - 125V - LED - Square - Black # F30ITSBS is universal and they are interchangeable, assuming you are staying within the same amperage rating.
I have added a link to our entire selection of power inlets as well as a link to a video review of the Furrion Marine Power Inlet # F30ITSBS. view full answer...
I do have some of the components that you will need to set your trailer up for a shore power circuit but if install cost is all you are looking for then you would be best off talking with a qualified service center as this is not something we partake in. The primary factor will be the shop's labor rate and that can very drastically so it would be best if you call around for this beforehand.
In order to install a shore power circuit you are going to need a transfer switch, power inlet,... view full answer...
Happy to help Bruce,
For a trailer conversion, a solid option is the WFCO 40A Auto-Detect Power Center # WFC72GR, it combines the 120V breaker panel, 12V fuse panel and converter/charger into one unit and supports both lead-acid and lithium batteries.
To complete the setup, you'll also need:
30 Amp Power Inlet # A10-30INBKVP
30 Amp Shore Power Cord # A10-3025EDBK
If you'll only be plugging into campground power, you won't need a transfer switch. Those are only necessary when switching... view full answer...
Just the cover is not available but we do offer the full replacement power inlet with the Furrion Replacement Power Inlet # 431861. view full answer...
The first thing you'll need is a power inlet to receive power from the shore power pedestal. You'll most likely only need 30amp service since you're in an enclosed trailer so I recommend the Hughes Autoformers Safe View Smart Power Inlet # HU66VR. You'll need to use at minimum 10AWG wire to connect this to a distribution center.
Now the you have an inlet for the power you need a distribution panel to run it to and distribute it to all of your appliances. For this I recommend the Progressive... view full answer...
In order to wire your cargo trailer for both 12 volt DC and 110 volt AC power you would need to install a AC/DC distribution panel and power converter which we currently do not offer. You would then wire the 12 volt power to the converter along with all of your 110 volt outlets.
In order to hook up to shore power you would first need to install a power inlet like the Epicord 30 Amp Twist Lock Power Inlet part # 277-000138. Once the power inlet is installed you would then need an electrical... view full answer...
You are correct in that in order to power AC and DC units with shore power, you need a converter. The Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 45 Amp, part # PD4045KA, that you looked at is a good choice for this. I've linked to a video review of this converter and included a picture of a typical setup.
Keep in mind that you will need a power inlet to get the shore power. If you don't already have one, you can use the Epicord 30 Amp Twist Lock Power Inlet... view full answer...
Yes, in order to set your trailer up for use with shore power you will first need an AC distribution panel. For this, I recommend a Progressive Dynamics Series AC Distribution Panel. In order to bring power into the panel you will also need a power inlet, the Epicord 30 Amp Twist Lock Power Inlet part # 277-000138 and a shore power cord, the Furrion RV Power Cord with Handle part # F3OR36SBOEM.
If you want to sometimes power the trailer with a generator you will also need an adapter for... view full answer...
Currently there is no adapter available to plug your 7-wire plug into 110v shore power. To power the lights and any other equipment in your Look Vision Trailer you would need to install a power inlet like the # 431861 and wire it to a distribution panel like the # PD4045KA. This panel can convert the AC current coming from your shore power to DC to allow you to run the lights and any other equipment in your trailer. You can add a battery like # 34276285 into this system to power your equipment... view full answer...
You are correct, the Furrion Marine Power Inlet # F30ITSBS is a direct replacement for your Furrion F30INSBS. Since you are needing a new power inlet I recommend going ahead and getting the # F30ITSBS due to this.
I included a video of the # F30ITSBS for you to take a look at. view full answer...
Hey Mike we have the Hughes part # HU87VR which would work great as a direct replacement for your Furrion power inlet. This inlet is really cool because it uses LEDs on the front of it to let you know that everything is working fine. If any of the LED lights are red and the halo light is red or not illuminating, theres a wiring problem at the power source. Consult the manual to determine if theres a missing ground, missing neutral, missing line, or reverse polarity. What camper do you have? view full answer...
Hey Tim, that's a nice trailer! Another way to power the winch on your 2017 Cargo Mate would be to have a large deep cell battery installed on the trailer that will power the winch and then use the 12 volt accessory circuit from the 7-way on your truck to put a maintenance charge on the battery. You could then run lights off of the same battery.
Or and this is my recommendation, if you have a winch with up to a 16.5k capacity you could get the Trailer and Vehicle Electric Winch Wiring... view full answer...
Yes. In order to use the SmartPlug Replacement RV Power Inlet - 50 Amp # SM56FR you will need to replace your old twist lock power cord with a SmartPlug RV Power Cord - 125/250V - 50 Amp - 30' # SM86FR. view full answer...
The Furrion Power Cord Adapter # F3030YSY is only available in yellow and does include the weather proof collars. The information in the product description and video is accurate, the male end of this cord is what plugs into the boat. view full answer...
A 50 amp power inlet like the Mighty Cord Replacement RV Power Inlet part # A10-50INVP will use a four wire system (two hot, one ground, and one neutral) whereas a 30 amp power inlet like the Mighty Cord Replacement RV Power Inlet part # 277-000137 will use a three wire system (one hot, one ground, and one neutral).
If you need a power cord to go from the inlet to shore power then I recommend using the Mighty Cord RV Power Cord Extension w/ Finger Grip Handle part # A10-5010EH for 10',... view full answer...
Go To Results